Wiki source code of 06 - Setup

Version 10.1 by Eric Nantel on 2022/04/06 09:30
Hide last authors
Eric Nantel 9.1 1 {{stepNavigation nextStepName="Return" previousStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-tracked/a4wd3-tracked-quickstart/a4wd3-tracked-tracks/" nextStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-tracked/a4wd3-tracked-quickstart/" pageTitle="A4WD3 Tracked - Setup"/}}
Eric Nantel 1.1 2
Eric Nantel 9.1 3 (% style="width:710px" %)
4 |(((
5 CAUTION: Before powering the motors, ensure they rotate in the same direction on each side. If the wiring between the motors and the Sabertooth was done correctly, the motors on each side of the robot should rotate in the same direction.
6
7 If the front and rear motors rotate in opposite directions however, the track which connects them will cause them to stall and burn very quickly! If you are at all uncertain, it is safest to remove the sprockets and test the motors. If they rotate in opposite directions, the wiring to the Sabertooth needs to be corrected.
8 )))
9
Eric Nantel 1.1 10 {{warningBox warningText="Radio Control (RC) Mode"/}}
11
12 (% style="width:710px" %)
Coleman Benson 7.1 13 |(% colspan="4" %)**1. Set the Sabertooth DIP Switches**
Coleman Benson 5.1 14 |(% style="width:35px" %) |(% style="text-align:center; width:350px" %)Sabertooth 2 x 12A Standard|(% style="width:35px" %) |**Typical Setup**
Eric Nantel 3.1 15 | |(% colspan="1" rowspan="6" style="text-align:center; vertical-align:middle" %)[[image:rover-kits.a4wd3-wheeled.a4wd3-wheeled-quickstart.a4wd3-wheeled-setup.WebHome@Sabertooth-2x12-Switches.png||alt="dip-switch-example.jpg"]]|(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:left; vertical-align:middle" %)OFF (Enable RC Mode)
Eric Nantel 1.1 16 | |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:left; vertical-align:middle" %)ON (Enable RC Mode)
17 | |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:left; vertical-align:middle" %)OFF (Lithium Battery Mode)
18 | |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:left; vertical-align:middle" %)ON (Enable Mixing Mode)
19 | |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:left; vertical-align:middle" %)ON (Disable Exponential)
20 | |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:left; vertical-align:middle" %)OFF (Disable Timeout)
Coleman Benson 7.1 21 | |(% colspan="3" rowspan="1" %)More Info: [[Sabertooth 2x12 - Dip Switch Wizard>>https://www.dimensionengineering.com/datasheets/SabertoothDIPWizard/start.htm]]
22 | |(% colspan="3" rowspan="1" %)More Info: [[Sabertooth 2x12 - User Guide>>https://www.dimensionengineering.com/datasheets/Sabertooth2x12.pdf]]
Eric Nantel 1.1 23 |(% colspan="4" %)**2. Connect the battery**
24 |(% colspan="4" %)**3. Enjoy**
25
26 {{warningBox warningText="Microcontroller / Autonomuous"/}}
27
28 (% style="width:710px" %)
Coleman Benson 7.1 29 |(% colspan="4" %)**1. Set the Sabertooth DIP Switches**
Coleman Benson 5.1 30 |(% style="width:35px" %) |(% style="text-align:center; width:350px" %)Sabertooth 2 x 12A Standard|(% style="width:35px" %) |(% style="text-align:center" %)**Typical Setup**
Eric Nantel 4.1 31 | |(% colspan="1" rowspan="6" style="text-align:center; vertical-align:middle" %)[[image:rover-kits.a4wd3-wheeled.a4wd3-wheeled-quickstart.a4wd3-wheeled-setup.WebHome@Sabertooth-2x12-Switches.png||alt="dip-switch-example.jpg"]]|(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:left; vertical-align:middle" %)OFF (Enable RC Mode)
Eric Nantel 1.1 32 | |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:left; vertical-align:middle" %)ON (Enable RC Mode)
33 | |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:left; vertical-align:middle" %)OFF (Lithium Battery Mode)
34 | |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:left; vertical-align:middle" %)ON (Enable Mixing Mode)
35 | |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:left; vertical-align:middle" %)ON (Disable Exponential)
36 | |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:left; vertical-align:middle" %)OFF (Disable Timeout)
Coleman Benson 5.1 37 | |(% colspan="3" rowspan="1" style="vertical-align:middle" %)More Info: [[Sabertooth 2x12 - Dip Switch Wizard>>https://www.dimensionengineering.com/datasheets/SabertoothDIPWizard/start.htm]]
38 | |(% colspan="3" rowspan="1" style="vertical-align:middle" %)More Info: [[Sabertooth 2x12 - User Guide>>https://www.dimensionengineering.com/datasheets/Sabertooth2x12.pdf]]
Eric Nantel 1.1 39 |(% colspan="4" %)**2. Connect the Sabertooth to your Microcontroller**
Eric Nantel 9.1 40 | |(% colspan="1" rowspan="9" style="text-align:center; vertical-align:middle" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-setup/WebHome/BBU-01-to-Sabertooth.png"/}}|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png" height="18" width="18"]]|(% style="text-align:left; vertical-align:middle" %)__Jumper on "VS"__ to use the Sabertooth as the power source for the BotBoarduino
Eric Nantel 1.1 41 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)__No Jumper__ to isolate the middle row and avoid conflicts
42 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)Ground or 0V
43 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)To "S1" on Sabertooth #1
44 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)To "S2" on Sabertooth #1
45 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)To "S1" on Sabertooth #2 (if equipped)
46 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)To "S2" on Sabertooth #2 (if equipped)
47 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)__Jumper on "Ext"__ to power the BotBoarduino from the Sabertooth 5V regulator
48 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="text-align:left; vertical-align:middle" %)__Jumper on "VL = VS"__ to link the two together
Coleman Benson 6.1 49 | |(% colspan="1" style="text-align:left; vertical-align:middle" %)More Info: [[BotBoarduino User Manual>>http://www.lynxmotion.com/images/html/build185.htm]]|(% style="text-align:center; vertical-align:middle" %) |(% style="text-align:left; vertical-align:middle" %)
Coleman Benson 5.1 50 |(% colspan="4" %)**3. Upload your code**
51 | |(% colspan="3" rowspan="1" style="vertical-align:middle" %)Sample Code: [[Lynxmotion GitHub - Arduino A4WD3 Examples>>https://github.com/Lynxmotion/Rovers/tree/master/A4WD3]]
Eric Nantel 1.1 52 |(% colspan="4" %)**4. Connect the battery**
53 |(% colspan="4" %)**5. Enjoy**
54
Eric Nantel 9.1 55 {{stepNavigation nextStepName="Return" previousStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-tracked/a4wd3-tracked-quickstart/a4wd3-tracked-tracks/" nextStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-tracked/a4wd3-tracked-quickstart/" pageTitle="A4WD3 Tracked - Setup"/}}

Navigation

Recently Visited

Copyright RobotShop 2018