BRAT Biped Autonomous Tutorial

<td valign="top" align="left">Biped BRAT Autonomous Tutorial.

Updated

6

12/20/2011

7

8

Safety first! Wear eye protection and never touch a powered robot!

9

Note: This tutorial uses the Bot Board II, BASIC Atom Pro 28, a Sharp GP2D12 sensor, and a Buffered

10

2-Axis Accelerometer (DE-11).

11

Software:

12

- BASIC Micro Studio

13

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/bratosf3.zip">BRAT Servo Offset Finder

14

Program v3</a> (09/16/09)

15

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat1.zip">Autonomous Walk Code</a>

16

(09/16/09)

17

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat2.zip">Autonomous GP2D12 Code</a>

18

(09/16/09)

19

-- Video: <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/avoid01.mpg">Avoiding an obstacle (mpg)</a>

20

-- Video: <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/break01.mpg">Taking a break (mpg)</a>

21

-- Video: <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/walkaway.mpg">Demonstrating proximity beeps (mpg)</a>

22

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat3.zip">Autonomous 1-Axis Accelerometer Code</a>

23

(09/16/09)

24

-- Video: <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/getup01.mpg">Getting up front and back (mpg)</a>

25

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat4.zip">Autonomous 2-Axis Accelerometer Code</a>

26

(09/16/09)

27

-- Video: <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/getup02.mpg">Getting up front and side (mpg)</a></td>

28

29

Image of Biped BRAT.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 1.

36

Make sure your servos are plugged into the appropriate channels, as shown in Table 1.

37

*Note, P9 is used by the speaker, so we can't plug a servo in there.</td>

<td >

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Bot Board I/O</td>

48

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Connection</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Left Ankle</td>

</tr>

<tr>

</tr>

<tr>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Right Ankle</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Right Knee</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Right Hip</td>

</tr>

</tbody></table>

</div></td>

</tr>

<tr>

Table 1.</td>

</tr>

</tbody></table>

</center></div>

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 2.

90

Make sure the Bot Board's jumpers are set according to Table 2.

91

Refer to Figure 2 for help with jumper settings.

92

*Note, the VS to AX0 jumper enables the program to monitor the servo battery voltage. When the battery is low,

93

the robot can beep in warning.</td>

<td >

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0" colspan="2">Bot Board II

Jumper Settings</td>

</tr>

<tr>

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Enable</td>

108

109

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">A, B, and C buttons</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">I/O Group 0-3</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">I/O Groups 4-7 and 8-11</td>

118

</tr>

119

<tr>

120

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Enable</td>

121

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">SPKEN (Speaker Enable)</td>

122

</tr>

123

<tr>

124

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Enable</td>

125

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">VS (Servo Voltage) to AX0 (P16)</td>

</tr>

</tbody></table>

</div></td>

</tr>

<tr>

Table 2.</td>

</tr>

</tbody></table>

</center></div>

</td>

</tr>

<tr>

</td>

</tr>

<tr>

Figure 2.

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 3.

153

Download and install the BASIC Micro Studio. Download the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/bratosf3.zip">BRAT Servo Offset Finder program</a>, and load it into the IDE.

154

Program the Atom Pro, and follow these instructions to find your robot's offsets.

155

<ul>

156

<li>Press A to decrease the servo offset by 5us.</li>

157

<li>Press C to increase the servo offset by 5us.</li>

158

<li>Press B to change which servo is being manipulated, and to

159

save your offsets. The order of the

160

program is shown in Figure 3.</li>

161

</ul>

162

Note, if you have the Speaker enabled, when you press the B button you will hear a short tone. The tone will

163

raise in pitch when you change from servo to servo, and will lower in pitch and be longer when you get back to Start.</td>

Figure 3.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step

174

4.

175

Place the robot in a position as close to neutral as possible, and turn it on. Your robot should go to and hold the neutral position, and should

176

resemble figures 4-1 through 4-3. If the joints are off by more than 15° you may have made an error in assembly. To correct this, remove the

177

center screw from the round servo horn, pull the servo horn off the servo, rotate until it's aligned, then reattach the servo horn.

178

Use the A, B, and C buttons to straighten the BRAT as shown in Figures

179

4-1, 4-2, and 4-3.

180

Note, if you are building the robot with HS-422 servos, you will notice the hip servos oscillate if the robot

181

is lifted off the ground. This is normal, and is due to the lower power servo. When the robot is walking, the effects are minimal. Using a

182

voltage that is higher than 6vdc will make the oscillations worse. When building a robot with more powerful servos such as HS-475,

183

HS-485, or HS-645, you

184

will not see this effect.

185

After you've cycled through the servos and adjusted them to match Figures

186

4-1 through 4-3, pressing the B button again will save your servo offset

187

values to the Atom Pro's EEPROM.

</td>

Figure 4-1.</td>

</tr>

<tr>

</tr>

<tr>

Figure 4-2.

</td>

Figure 4-3.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step

211

5.

212

Now download the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat1.zip">BRAT Autonomous Walk Code</a>, load it into the

213

IDE, and program your BRAT.

214

Congratulations, your BRAT will now be able to walk around! The autonomous walk program will make the BRAT

215

follow this sequence: walk, walk, walk, turn, long-stride, long-stride, kick, turn, stop.

216

To change the behavior of your robot, you can modify the code below the label "main" and above the

217

label "move". You can also create sequences following the format shown in the code below the label "move". We will provide

218

several more code examples including common sensors.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step

225

6.

226

Use double-sided tape to attach the GP2D12 sensor to the BRAT's head area. The exact position doesn't matter too much, as long as the sensor is

227

facing toward the front of the robot.

228

Plug the sensor in to the channel shown in the following table.

<td >

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Bot Board I/O</td>

238

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Connection</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">GP2D12 Sensor</td>

</tr>

</tbody></table>

</div></td>

</tr>

<tr>

Table 6.</td>

</tr>

</tbody></table>

</center></div>

</td>

Figure 6.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step

263

7.

264

Now download the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat2.zip">BRAT Autonomous GP2D12 Code</a>, load it into the

265

IDE, and program your BRAT.

266

Congratulations, your BRAT will now be able to roam without bumping into anything! We also added a

267

"behavior" looping counter so the robot will periodically go into a resting position. You can edit the pauses to change how long it

268

rests and you can change the value of the looping counter to change how often it rests. The GP2D12 sensor is read before each step when the

269

robot is walking forward. You will hear a short low beep if nothing is detected. If an object is detected, the beep raises in pitch depending on

270

how close the object is. When the object is about 8" away, the robot will back up one step, turn left two steps, then continue forward. The

271

code also illuminates LEDs depending on which command is being processed.

272

Check out these videos:

273

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/avoid01.mpg">Avoiding an obstacle (mpg)</a>

274

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/break01.mpg">Taking a break (mpg)</a>

275

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/walkaway.mpg">Demonstrating proximity beeps (mpg)</a></td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step

283

8.

284

Use double-sided tape to attach the accelerometer sensor to the BRAT's head area. With the accelerometer, the sensor's physical position

285

isn't as important as the axis orientation. Make sure you follow the orientation shown in Figure

286

8.

287

Plug the sensor in to the channel shown in the following table.

<td >

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Bot Board I/O</td>

297

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Connection</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Accelerometer Sensor - Y Axis

302

(Used for Front-to-back tilt)</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Accelerometer Sensor - X Axis

307

(Used for Side-to-side tilt)</td>

</tr>

</tbody></table>

</div></td>

</tr>

<tr>

Table 8.</td>

</tr>

</tbody></table>

</center></div>

</td>

Figure 8.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step

328

9.

329

Now download the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat3.zip">BRAT Autonomous 1-Axis Accelerometer Code</a>, load it into the

330

IDE, and program your BRAT.

331

For this program, we are only using the values from the Y Axis. The Y Axis measures the

332

front-to-back tilt, so the BRAT can tell when it has fallen onto its back or front. We will incorporate the X Axis in a later program.

333

Congratulations, your BRAT will now be able to roam without bumping into anything, and get back up if it falls!

334

Check out this video:

335

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/getup01.mpg">Getting up front and back (mpg)</a></td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step

342

10.

343

Now download the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/abrat4.zip">BRAT Autonomous 2-Axis Accelerometer Code</a>, load it into the

344

IDE, and program your BRAT.

345

For this program, we have added the accelerometer's X Axis to measure side-to-side tilt. Now if the BRAT falls

346

onto its side, it will know to roll over in order to get back up. We have also incorporated a more advanced "get up from back"

347

routine, which will enable robots with lots of cabling or weight in the back to stand one foot at a time. Additionally, we've added a

348

"startled" behavior. If the BRAT is in resting mode and something is suddenly detected by the GP2D12 sensor, the BRAT will be

349

startled, lean back, and beep.

350

Congratulations, your BRAT will now be able to roam without bumping into anything, and get back up if it falls!

351

Check out this video:

352

- <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-autonomous/WebHome/getup02.mpg">Getting up front and side (mpg)</a></td>

</tr>

</tbody></table>

</body>

Wiki source code of BRAT Biped Autonomous Tutorial

Navigation