Turntable Assembly Guide v1.0

1	{{html wiki="false" clean="true"}}
2	<body><table border="0" cellpadding="0" cellspacing="0" >
3	<tbody><tr>
4	<td valign="top" ><font size="2" face="Verdana"><strong>Turntable
5	Assembly Guide v1.0. </strong></font>
6	<p><font size="2" face="Verdana"><strong>Updated <!--webbot
7	bot="Timestamp" startspan s-type="EDITED" s-format="%m/%d/%Y" -->
8	<!-- #BeginDate format:Am3 -->12/21/2011<!-- #EndDate -->
9	<!--webbot
10	bot="Timestamp" i-checksum="12506" endspan --></strong></font></p>
11	<p><font face="Verdana" size="2"><b>Safety first!</b> Wear eye protection and never touch a powered robot!</font></p>
12	</td>
13	<td align="center" valign="top" width="320"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base07a.jpg" border="2" hspace="10" ><br>
14	<font size="2" face="Verdana"><strong>Turntable complete</strong></font></td>
15	</tr>
16	<tr>
17	<td colspan="2" valign="top"> </td>
18	</tr>
19	<tr>
20	<td valign="top" ><font size="2" face="Verdana"><b>Step 1.</b><br>
21	Insert the stainless steel pins into the plastic bearings as shown.<font face="Verdana, Helvetica, sans-serif" size="2"><br>
22	</font>
23	<table border="0" >
24	<tbody><tr>
25	<td ><font size="2" face="Verdana"><b>5 x</b></font></td>
26	<td ><font size="2" face="Verdana"><b> </b></font></td>
27	</tr>
28	<tr>
29	<td ><font size="2" face="Verdana"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/basepin.gif" border="2" ></font></td>
30	<td ><font size="2" face="Verdana"><b> </b></font></td>
31	</tr>
32	</tbody></table>
33	</font></td>
34	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base01.jpg" border="2" hspace="10" ><br>
35	<font size="2" face="Verdana">Figure 1.</font></td>
36	</tr>
37	<tr>
38	<td colspan="2" valign="top"> </td>
39	</tr>
40	<tr>
41	<td valign="top" ><font size="2" face="Verdana"><b>Step 2.</b><br>
42	Install the bearings into the base as shown. They will fit snugly.</font>
43	<p><font size="2" face="Verdana">Note, the notch in the bottom edge of the
44	base indicates the back.</font></p>
45	</td>
46	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base02.jpg" border="2" hspace="10" ><br>
47	<font size="2" face="Verdana">Figure 2.</font></td>
48	</tr>
49	<tr>
50	<td valign="top" align="left" colspan="2"><br class="pb">
51	</td>
52	</tr>
53	<tr>
54	<td valign="top" ><font size="2" face="Verdana"><b>Step 3.</b><br>
55	Lay a piece of 400 grit sandpaper on a flat surface and move the base
56	(upside down) in small circles on it. This will remove any imperfections
57	on the bearings.</font></td>
58	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base03.jpg" border="2" hspace="10" ><br>
59	<font size="2" face="Verdana">Figure 3.</font></td>
60	</tr>
61	<tr>
62	<td colspan="2" valign="top"> </td>
63	</tr>
64	<tr>
65	<td valign="top" ><font size="2" face="Verdana"><b>Step 4.</b><br>
66	Figure 4 shows the circle pattern on the sandpaper and the inset shows the
67	bearings after any imperfections have been removed.</font></td>
68	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base04.jpg" border="2" hspace="10" ><br>
69	<font size="2" face="Verdana">Figure 4.</font></td>
70	</tr>
71	<tr>
72	<td colspan="2" valign="top"> </td>
73	</tr>
74	<tr>
75	<td valign="top" ><font size="2" face="Verdana"><b>Step 5.<br>
76	</b>Figure 5 illustrates a typical standard-size servo with its output
77	horn (the round white part) at center position. Make sure your servo looks
78	like the image, and then carefully remove the servo horn screw and pull
79	the horn straight off of the servo.</font></td>
80	<td align="center" valign="bottom" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/servo02.jpg" border="2" hspace="10" ><br>
81	<font size="2" face="Verdana">Figure 5.</font></td>
82	</tr>
83	<tr>
84	<td valign="top" align="left" colspan="2"><br class="pb">
85	</td>
86	</tr>
87	<tr>
88	<td valign="top" ><font size="2" face="Verdana"><b>Step 6.</b><br>
89	Place the servo in the base as shown and screw it in tightly using four #4
90	tapping screws.<font face="Verdana, Helvetica, sans-serif" size="2"><br>
91	</font>
92	<table border="0" >
93	<tbody><tr>
94	<td ><font size="2" face="Verdana"><b>4 x</b></font></td>
95	<td ><b> </b></td>
96	</tr>
97	<tr>
98	<td ><font size="2" face="Verdana"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/4375phts.gif" border="2" ></font></td>
99	<td ><b> </b></td>
100	</tr>
101	</tbody></table>
102	</font></td>
103	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base05.jpg" border="2" hspace="10" ><br>
104	<font size="2" face="Verdana">Figure 6.</font></td>
105	</tr>
106	<tr>
107	<td valign="top" colspan="2"> </td>
108	</tr>
109	<tr>
110	<td valign="top" ><font size="2" face="Verdana"><b>Step 7.<br>
111	</b>Add a drop of 3-in-1 oil to each bearing.</font></td>
112	<td align="center" valign="bottom" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base15.jpg" border="2" hspace="10" ><br>
113	<font size="2" face="Verdana">Figure 7.</font></td>
114	</tr>
115	<tr>
116	<td colspan="2" valign="top"> </td>
117	</tr>
118	<tr>
119	<td valign="top" ><font size="2" face="Verdana"><b>Step 8.</b><br>
120	Install the base top. The hole pattern should line up as shown in Figure
121	8, with one line pointing to the servo wire hole, and all of the lines
122	pointing between the mounting tabs.</font>
123	<p><font size="2" face="Verdana">Note, this top piece is manufactured to
124	be a tight fit. You might have to press very hard.</font></p>
125	<p><font size="2" face="Verdana">Attach the top with the servo horn screw.</font></p></td>
126	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base07a.jpg" border="2" hspace="10" ><br>
127	<font size="2" face="Verdana">Figure 8.</font></td>
128	</tr>
129	<tr>
130	<td valign="top" align="left" colspan="2"><br class="pb">
131	</td>
132	</tr>
133	<tr>
134	<td valign="top" ><font size="2" face="Verdana"><b>Step 9.</b><br>
135	Route the base servo's cable through the hole in the back of the base.
136	This will keep the base level to the mounting surface.</font></td>
137	<td align="center" valign="top" ><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-misc-mechanical/base-rotate-v1.0/WebHome/base08.jpg" border="2" hspace="10" ><br>
138	<font size="2" face="Verdana">Figure 9.</font></td>
139	</tr>
140	</tbody></table>
141	</body>
142	{{/html}}