Changes for page LSS-P - Electrical

Last modified by Eric Nantel on 2024/07/03 09:43
From version < 5.1 >
edited by Eric Nantel
on 2023/06/22 11:43
To version < 11.1 >
edited by Eric Nantel
on 2023/07/07 13:08
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,5 +1,10 @@
1 1  {{warningBox warningText="More information coming soon"/}}
2 2  
3 +
4 +
5 +
6 +
7 +
3 3  **Page Contents**
4 4  
5 5  {{toc/}}
... ... @@ -8,13 +8,12 @@
8 8  
9 9  In order to daisy chain one servo to the next (serial mode only), rollover serial cables are used. Although the wires are straight, one connector must be rotated 180 degrees with respect to the other.
10 10  
16 +(% style="width:800px" %)
11 11  |(% style="text-align:center; width:350px" %)**Serial Single**|(% style="text-align:center; width:350px" %)**Serial Multiples**
12 12  |(% style="width:350px" %)(((
13 -(% style="text-align:center" %)
14 -[[image:[email protected]||width="200"]]
19 +{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-Wiring-Single.png" width="400"/}}
15 15  )))|(% style="width:350px" %)(((
16 -(% style="text-align:center" %)
17 -[[image:[email protected]||width="200"]]
21 +{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-Wiring-Dual.png" width="400"/}}
18 18  )))
19 19  
20 20  = Wiring Pinout =
... ... @@ -22,9 +22,6 @@
22 22  |(% colspan="3" style="width:350px" %)**CAN Bus**
23 23  |(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**
24 24  |(% rowspan="3" style="width:350px" %)(((
25 -(% style="text-align:center" %)
26 -[[image:[email protected]||width="200"]]
27 -
28 28  
29 29  )))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)(((
30 30  **Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
... ... @@ -35,7 +35,6 @@
35 35  |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
36 36  |(% colspan="3" style="width:350px" %)**Power**
37 37  |(% colspan="1" rowspan="2" style="width:350px" %)(((
38 -(% style="text-align:center" %)
39 -[[image:[email protected]||width="200"]]
39 +
40 40  )))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**:
41 41  |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:
LSS-P-Wiring-Dual.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +393.1 KB
Content
LSS-P-Wiring-Single.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +319.2 KB
Content
Copyright RobotShop 2018