Wiki source code of LSS-P - Electrical
Version 6.1 by Eric Nantel on 2023/06/22 11:44
Hide last authors
 |
5.1 | 1 | {{warningBox warningText="More information coming soon"/}} |
| 2 | |||
| |
2.1 | 3 | **Page Contents** |
| 4 | |||
| 5 | {{toc/}} | ||
| 6 | |||
| 7 | = Typical Connections = | ||
| 8 | |||
| 9 | In order to daisy chain one servo to the next (serial mode only), rollover serial cables are used. Although the wires are straight, one connector must be rotated 180 degrees with respect to the other. | ||
| 10 | |||
| |
3.1 | 11 | |(% style="text-align:center; width:350px" %)**Serial Single**|(% style="text-align:center; width:350px" %)**Serial Multiples** |
| 12 | |(% style="width:350px" %)((( | ||
| |
6.1 | 13 | |
| |
3.1 | 14 | )))|(% style="width:350px" %)((( |
| |
6.1 | 15 | |
| |
3.1 | 16 | ))) |
| |
2.1 | 17 | |
| 18 | = Wiring Pinout = | ||
| 19 | |||
| |
3.1 | 20 | |(% colspan="3" style="width:350px" %)**CAN Bus** |
| 21 | |(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode** | ||
| 22 | |(% rowspan="3" style="width:350px" %)((( | ||
| 23 | |||
| 24 | )))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)((( | ||
| |
2.1 | 25 | **Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin |
| 26 | ))) | ||
| |
3.1 | 27 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)((( |
| 28 | **Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output. | ||
| 29 | ))) | ||
| 30 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground"). | ||
| 31 | |(% colspan="3" style="width:350px" %)**Power** | ||
| 32 | |(% colspan="1" rowspan="2" style="width:350px" %)((( | ||
| |
6.1 | 33 | |
| |
3.1 | 34 | )))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**: |
| 35 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: |