Last modified by Eric Nantel on 2024/10/04 08:08
From version < 105.1 >
edited by Eric Nantel
on 2024/07/12 10:13
To version < 76.1 >
edited by Eric Nantel
on 2024/07/12 08:12
< >
Change comment: Upload new image "LSS-P-Config-Firmware-Download.png", version 1.2

Summary

Details

Page properties
Content
... ... @@ -83,8 +83,9 @@
83 83  
84 84  In order to view the various commands available for each drop-down, a PRO servo needs to be properly connected to the computer, powered, turned on and detected.
85 85  
86 -=== Query ===
86 +[[image:LSS-P-Config-ServoControl.png]]Query
87 87  
88 +
88 88  [[image:LSS-P-Config-Query.png]]
89 89  
90 90  1. The drop down list below Query provides a list of most query commands possible. More information click HERE
... ... @@ -93,6 +93,8 @@
93 93  
94 94  === Action ===
95 95  
97 +The drop down list below Action provides a list of most action commands used with the LSS PRO servos.
98 +
96 96  [[image:LSS-P-Config-Action.png]]
97 97  
98 98  1. The drop down list below Action provides a list of most action commands possible. More information click HERE.
... ... @@ -102,6 +102,8 @@
102 102  
103 103  === Configuration ===
104 104  
108 +The drop down list below Configuration provides a list of most configuration commands used with the LSS PRO servos.
109 +
105 105  [[image:LSS-P-Config-Config.png]]
106 106  
107 107  1. The drop down list below Configuration provides a list of most configuration commands possible. More information click HERE.
... ... @@ -158,7 +158,7 @@
158 158  1. Two separate "Add" button and drop down are present, they are shortcuts to add to the action bellow.
159 159  1. Action command that will be sent to the actuator plus displayed units for the interface.
160 160  
161 -== Firmware Update ==
166 +== Firmware ==
162 162  
163 163  It is good to periodically check for firmware updates for the servos. A firmware update requires that the computer running the software be connected to the Internet.
164 164  
... ... @@ -170,31 +170,22 @@
170 170  
171 171  Note: Only a servo connected via USB can be updated and all the other servos on the bus will not be displayed with a green logo unless connected directly via USB.
172 172  
173 -=== Online Update ===
178 +=== Updating ===
174 174  
175 -1. Select the servo ID that requires a firmware update
180 +1. Select the servo that requires a firmware update
176 176  1. If the logo is green, click on the "Firmware Update" button
177 177  1. A message will ask you if you want do download the latest firmware, click Yes.
178 -[[image:LSS-P-Config-Firmware-Download-Yes.png||alt="LSS-P-Config-Firmware-Download.png"]]
183 +[[image:LSS-P-Config-Firmware-Download.png]]
179 179  1. It's pretty quick but once downloaded another message will ask you if you want to proceed click Yes.
180 -[[image:LSS-P-Config-Firmware-Write-Acknowledge.png]]
185 +[[image:LSS-P-Config-Firmware-Write.png]]
181 181  1. The servo will be put in "Firmware Update" mode and flashing will start. A progress bar will show the progress. DO NOT UNPLUG / UNPOWER the servo while updating.
182 182  [[image:LSS-P-Config-Firmware-Uploading.png]]
183 -1. Once the procedure is done you will have a confirmation pop-up.
184 -[[image:LSS-P-Config-Firmware-Success.png]]
188 +1. sdf
185 185  
186 -=== Offline Update ===
190 +=== ===
187 187  
188 -In some rare occasions, our staff could ask you to try a firmware which they provided and here's how to flash it.
192 +[[image:LSS-P-Config-Firmware-Local.png]]
189 189  
190 -1. Select the servo ID that requires a firmware update
191 -1. Click on the "Firmware Update" button and depending on the pop-up select as shown. 
192 -[[image:LSS-P-Config-Firmware-Download-No.png||alt="LSS-P-Config-Firmware-Download.png"]] [[image:LSS-P-Config-Firmware-Write-Yes.png||alt="LSS-P-Config-Firmware-Local.png"]]
193 -1. Browse and select & open the firmware file provided by our staff.
194 -[[image:LSS-P-Config-Firmware-Local-Browse.png]]
195 -1. Another message will ask you if you want to proceed click Yes.
196 -[[image:LSS-P-Config-Firmware-Write-Acknowledge.png]]
197 -1. The servo will be put in "Firmware Update" mode and flashing will start. A progress bar will show the progress. DO NOT UNPLUG / UNPOWER the servo while updating.
198 -[[image:LSS-P-Config-Firmware-Uploading.png]]
199 -1. Once the procedure is done you will have a confirmation pop-up.
200 200  [[image:LSS-P-Config-Firmware-Success.png]]
195 +
196 +
LSS-P-Config-Firmware-Download-No.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -9.6 KB
Content
LSS-P-Config-Firmware-Download-Yes.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -9.5 KB
Content
LSS-P-Config-Firmware-Local-Browse.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -28.5 KB
Content
LSS-P-Config-Firmware-Write-Acknowledge.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -9.2 KB
Content
LSS-P-Config-Firmware-Write-Yes.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -10.0 KB
Content

Navigation

Copyright RobotShop 2018