Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • LSS-P-S1-Pinout-RJ45.png

Details

Page properties

Content

...	...	@@ -6,6 +6,9 @@
6	6
7	7
8	8
	9	+
	10	+
	11	+
9	9	**Page Contents**
10	10
11	11	{{toc/}}
...	...	@@ -26,15 +26,16 @@
26	26
27	27	|(% colspan="3" style="width:350px" %)**CAN Bus**
28	28	|(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**
29		-|(% rowspan="3" style="width:350px" %)(((
30		-
31		-)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Yellow.png]]|(% style="text-align:left; vertical-align:middle" %)(((
32		-**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
	32	+|(% rowspan="4" style="width:350px" %)(((
	33	+{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-RJ45.png"/}}
	34	+)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png]]|(% style="text-align:left; vertical-align:middle" %)(((
	35	+**CAN High:**
33	33	)))
34		-|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)(((
35		-**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
	37	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)(((
	38	+**CAN Low**
36	36	)))
37		-|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
	40	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:
	41	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Not Connected:** Those pins are un-connected
38	38	|(% colspan="3" style="width:350px" %)**Power**
39	39	|(% colspan="1" rowspan="2" style="width:350px" %)(((
40	40	{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-Power.png"/}}

LSS-P-S1-Pinout-RJ45.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+111.7 KB

Content