Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,5 +1,13 @@
1	1	{{warningBox warningText="More information coming soon"/}}
2	2
	3	+
	4	+
	5	+
	6	+
	7	+
	8	+
	9	+
	10	+
3	3	**Page Contents**
4	4
5	5	{{toc/}}
...	...	@@ -20,15 +20,16 @@
20	20
21	21	|(% colspan="3" style="width:350px" %)**CAN Bus**
22	22	|(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**
23		-|(% rowspan="4" style="width:350px" %)(((
	31	+|(% rowspan="5" style="width:350px" %)(((
24	24	{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-RJ45.png"/}}
25		-)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png]]|(% style="text-align:left; vertical-align:middle" %)(((
26		-**CAN High:**
	33	+)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Yellow.png]]|(% style="text-align:left; vertical-align:middle" %)(((
	34	+**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
27	27	)))
28		-|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Yellow.png]]|(% style="text-align:left; vertical-align:middle" %)(((
29		-**CAN Low**
	36	+|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png]]|(% style="text-align:left; vertical-align:middle" %)(((
	37	+**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
30	30	)))
31		-|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:
	39	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
	40	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Power: **
32	32	|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Not Connected:** Those pins are un-connected
33	33	|(% colspan="3" style="width:350px" %)**Power**
34	34	|(% colspan="1" rowspan="2" style="width:350px" %)(((