Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,5 +1,13 @@
1	1	{{warningBox warningText="More information coming soon"/}}
2	2
	3	+
	4	+
	5	+
	6	+
	7	+
	8	+
	9	+
	10	+
3	3	**Page Contents**
4	4
5	5	{{toc/}}
...	...	@@ -19,15 +19,17 @@
19	19	= Wiring Pinout =
20	20
21	21	|(% colspan="3" style="width:350px" %)**CAN Bus**
22		-|(% rowspan="4" style="width:350px" %)(((
	30	+|(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**
	31	+|(% rowspan="5" style="width:350px" %)(((
23	23	{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-RJ45.png"/}}
24		-)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png]]|(% style="text-align:left; vertical-align:middle" %)(((
25		-**CAN High:**
	33	+)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Yellow.png]]|(% style="text-align:left; vertical-align:middle" %)(((
	34	+**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
26	26	)))
27		-|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Yellow.png]]|(% style="text-align:left; vertical-align:middle" %)(((
28		-**CAN Low**
	36	+|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-attachments.WebHome@SQUARE-Green.png]]|(% style="text-align:left; vertical-align:middle" %)(((
	37	+**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
29	29	)))
30		-|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:
	39	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
	40	+|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Power: **
31	31	|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Not Connected:** Those pins are un-connected
32	32	|(% colspan="3" style="width:350px" %)**Power**
33	33	|(% colspan="1" rowspan="2" style="width:350px" %)(((