Wiki source code of LSS-P - Electrical
Version 31.2 by Eric Nantel on 2024/04/19 14:14
Show last authors
| 1 | {{warningBox warningText="More information coming soon"/}} |
| 2 | |
| 3 | |
| 4 | **Page Contents** |
| 5 | |
| 6 | {{toc/}} |
| 7 | |
| 8 | = Typical Connections = |
| 9 | |
| 10 | In order to daisy chain one servo to the next (serial mode only), rollover serial cables are used. Although the wires are straight, one connector must be rotated 180 degrees with respect to the other. |
| 11 | |
| 12 | (% style="width:800px" %) |
| 13 | |(% style="text-align:center; width:350px" %)**Serial Single**|(% style="text-align:center; width:350px" %)**Serial Multiples** |
| 14 | |(% style="width:350px" %)((( |
| 15 | {{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-Wiring-Single.png" width="400"/}} |
| 16 | )))|(% style="width:350px" %)((( |
| 17 | {{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-Wiring-Dual.png" width="400"/}} |
| 18 | ))) |
| 19 | |
| 20 | = Wiring Pinout = |
| 21 | |
| 22 | |(% colspan="3" style="width:350px" %)**CAN Bus** |
| 23 | |(% rowspan="4" style="width:350px" %)((( |
| 24 | {{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-RJ45.png"/}} |
| 25 | )))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)((( |
| 26 | **#4: **CAN High |
| 27 | ))) |
| 28 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)((( |
| 29 | **#5: **CAN Low |
| 30 | ))) |
| 31 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**#7, 8: **Ground (GND) |
| 32 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**#1, 2, 3, 6:** Not Connected |
| 33 | |(% colspan="3" style="width:350px" %)**Power** |
| 34 | |(% colspan="1" rowspan="2" style="width:350px" %)((( |
| 35 | {{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-Power.png"/}} |
| 36 | )))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**: |
| 37 | |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: |