Changes for page FlowArm LSS
Last modified by Eric Nantel on 2024/07/03 09:39
Change comment: There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 1 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,6 +1,6 @@ 1 - [[image:LSS-FlowArm.png||width="350"]]1 +{{lightbox image="LSS-FlowArm.png" width="400"/}} 2 2 3 -[[image:lynxmotion-wiki-attachments.WebHome@ ComingSoon.jpg||alt="wiki-download.png"]]3 +[[[[image:lynxmotion-wiki-attachments.WebHome@DownloadNow.png]]>>https://www.lynxmotion.com/tools/LSS_FlowArm.zip]] 4 4 5 5 **Page Contents** 6 6 ... ... @@ -28,11 +28,7 @@ 28 28 29 29 Before assembling the arm, each of the IDs assigned to the servos must correspond with what is needed in the software. 30 30 31 -* Base: 1 32 -* Shoulder: 2 33 -* Elbow: 3 34 -* Wrist: 4 35 -* Gripper: 5 31 +{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-articulated-arm/lss-articulated-arm-servo-setup/WebHome/SESV2-LSS-ARTICULATED-ARM-IDS.PNG" width="350"/}} 36 36 37 37 To do so, the [[LSS Configuration Software>>doc:lynxmotion-smart-servo.lss-configuration-software.WebHome]] is used. Follow the procedure outlined here: [[doc:lynxmotion-smart-servo.lss-configuration-software.lss-config-configure-ids.WebHome]] 38 38 ... ... @@ -40,23 +40,22 @@ 40 40 * Servos have been assembled in correct orientation (as per assembly manual) 41 41 * Servo offsets have been updated if necessary (see procedure below). 42 42 43 -The next important step is "STORE OFFSETS" explained below. 44 - 45 45 == Connecting via USB == 46 46 47 -The simplest way to connect is directly using an RS232 to USB cable. Here are the steps you need to follow in order to set this up. Follow the steps below:41 +The simplest way to connect is directly using the [[LSS-Adapter>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]] (or any RS232 to USB interface). Here are the steps you need to follow in order to set this up. Follow the steps below: 48 48 49 49 1. Connect the USB cable to the LSS Adapter board on your robot 50 50 1. Plug the USB connector into the PC 45 +1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable 51 51 1. Connect the power to the LSS Adapter via the yellow XT60 plug 52 52 1. Power on the robot (On/Off switch) 53 53 1. Start the LSS FlowArm software 54 -1. Select the appropriate COM port from the drop-down list 49 +1. Select the appropriate COM port from the drop-down list & the baudrate (115200) 55 55 1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established. 56 56 57 57 == Connecting via Bluetooth == 58 58 59 -If you have purchased a Bluetooth module which is in XBee format, ensure 54 +If you have purchased a Bluetooth module which is in XBee format, ensure to have the right baudrate on your bluetooth adapter, the default is 115 200 for the LSS. 60 60 61 61 = Interface = 62 62
- LSS-flowarm-30812.jpg
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -260.5 KB - Content