Changes for page FlowArm LSS

Last modified by Eric Nantel on 2024/07/03 09:39
From version < 63.2 >
edited by Eric Nantel
on 2019/09/23 10:46
To version < 93.1 >
edited by Eric Nantel
on 2019/10/17 15:14
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,6 @@
1 -[[image:LSS-FlowArm.png||width="350"]]
1 +{{lightbox image="LSS-FlowArm.png" width="400"/}}
2 2  
3 -[[image:lynxmotion-wiki-attachments.WebHome@ComingSoon.jpg||alt="wiki-download.png"]]
3 +[[[[image:lynxmotion-wiki-attachments.WebHome@DownloadNow.png]]>>https://www.lynxmotion.com/tools/LSS_FlowArm.zip]]
4 4  
5 5  **Page Contents**
6 6  
... ... @@ -42,22 +42,27 @@
42 42  
43 43  1. Connect the USB cable to the LSS Adapter board on your robot
44 44  1. Plug the USB connector into the PC
45 +1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable
45 45  1. Connect the power to the LSS Adapter via the yellow XT60 plug
46 46  1. Power on the robot (On/Off switch)
47 47  1. Start the LSS FlowArm software
48 -1. Select the appropriate COM port from the drop-down list
49 +1. Select the appropriate COM port from the drop-down list & the baudrate (115200)
49 49  1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established.
50 50  
51 51  == Connecting via Bluetooth ==
52 52  
53 -If you have purchased a Bluetooth module which is in XBee format, ensure
54 +If you have purchased a Bluetooth module which is in XBee format, ensure to have the right baudrate on your bluetooth adapter, the default is 115 200 for the LSS.
54 54  
55 55  = Interface =
56 56  
57 57  == Header ==
58 58  
59 -[[image:lss-flowarm-header.jpg]]
60 +[[image:lss-flowarm-header.png||alt="lss-flowarm-header"]]
60 60  
62 +**EMERGENCY STOP**
63 +
64 +At any given time you can click this button to stop the arm. This will send a "LIMP" command directly to all servos.
65 +
61 61  **STORE OFFSETS**
62 62  
63 63  The "STORE OFFSETS" button configures all of the servo offsets (this makes use of the CO command as part of the [[LSS Communication Protocol>>doc:lynxmotion-smart-servo.lss-communication-protocol.WebHome]]). Before pressing the button, orient the arm as shown below (with the gripper closed), and only then click the STORE OFFSETS button.
... ... @@ -68,11 +68,12 @@
68 68  * Wrist servo along R axis (parallel to elbow to wrist)
69 69  * Gripper servo closed
70 70  
71 -[[image:lss-flowarm-offsets.jpg]]
76 +(% style="width:700px" %)
77 +|(% style="text-align:center; vertical-align:middle" %)[[image:lss-flowarm-offset-left.png||alt="lss-flowarm-left.png" height="300" width="300"]]|(% style="text-align:center; vertical-align:middle" %)[[image:lss-flowarm-offset-top.png||alt="lss-flowarm-top.png" height="300" width="300"]]
72 72  
73 73  **LIMP**
74 74  
75 -Causes all servos to immediately go LIMP (i.e. lose torque). The arm will collapse. It's important to note that the software will not constantly query all servos for their position, and as such the virtual arm on screen will not update frequently if at all. If you want the virtual arm on screen to update as you move the real arm, use TEACH mode described below.
81 +Causes all servos to slowly go LIMP (i.e. lose torque), gradually loosing torque until hitting the ground. It's important to note that the software will not constantly query all servos for their position, and as such the virtual arm on screen will not update frequently if at all. If you want the virtual arm on screen to update as you move the real arm, use TEACH mode described below.
76 76  
77 77  **STOP**
78 78  
... ... @@ -117,13 +117,13 @@
117 117  
118 118  The left view is a representation of the arm, where the orange circles represent the location of each axis of rotation. You can move the arm in this view by clicking on and dragging the wrist rotation servo.
119 119  
120 -[[image:lss-flowarm-side-view.jpg]]
126 +[[image:lss-flowarm-left.png||width="300"]]
121 121  
122 122  **Top View**
123 123  
124 124  The top view shows the arm top down. You can move the arm within this view by clicking on and dragging the wrist rotation servo.
125 125  
126 -**[[image:lss-flowarm-top-view.jpg]]**
132 +**[[image:lss-flowarm-top.png||width="300"]]**
127 127  
128 128  === Shortcuts ===
129 129  
... ... @@ -145,20 +145,15 @@
145 145  
146 146  **Gripper**
147 147  
148 -Assuming the gripper has been properly calibrated, The number below represents the opening at the tip. Fully closed should correspond to 0 degrees. In order to grasp an object, DO NOT have the servo rotate to a position which it cannot reach. In order to ensure the gripper servo does not go into error mode, the gripper should not exert much force on the object.
154 +Assuming the gripper has been properly calibrated, The number below represents the opening at the tip. Fully closed should correspond to 0 degrees. We added a feature where the servo stop when it feel a current raising, this allows the user to ask for a full close and have a good grip on the item picked.
149 149  
150 -1. Close the gripper to a position just slightly larger than the object
151 -1. Using the arrows, close the gripper until friction between the foam and the object prevent the object from falling out or moving.
152 -1. DO NOT apply too much pressure, or else the servo's current will spike and it will go into error mode and need to be reset.
153 -1. Use the last position as the "fully closed" position for the gripper for that object, in that specific orientation.
156 +[[image:lss-flowarm-gripper-view.png||alt="lss-flowarm-gripper-view.jpg"]]
154 154  
155 -[[image:lss-flowarm-gripper-view.jpg]]
156 -
157 157  **Wrist**
158 158  
159 159  The wrist angle can be locked or unlocked. The field allows for user input (click the numbers) or fine adjustments using the arrows.
160 160  
161 -[[image:lss-flowarm-wrist-view.jpg]]
162 +[[image:lss-flowarm-wrist-view.png||alt="lss-flowarm-wrist-view.jpg"]]
162 162  
163 163  **End Effector Position**
164 164  
... ... @@ -192,6 +192,7 @@
192 192  |(% style="width:257px" %)[[image:lss-flowarm-lock.jpg]]|(% style="width:306px" %)Lock |(% style="width:758px" %)Timeline locking
193 193  |(% style="width:257px" %)[[image:lss-flowarm-loop.jpg]]|(% style="width:306px" %)Repeat / Loop Pattern|(% style="width:758px" %)Play once or loop; Set the playback speed using the up and down arrows.
194 194  |(% style="width:257px" %)[[image:lss-flowarm-play.jpg]]|(% style="width:306px" %)Sequence Playback|(% style="width:758px" %)Restart sequence, play or stop
196 +|(% style="width:257px" %)[[image:lss-flowarm-inspector.png]]|(% style="width:306px" %)Frame Inspector|(% style="width:758px" %)Allows to modify the values sent in a particular frame manually.
195 195  
196 196  **Sequences**
197 197  
... ... @@ -291,6 +291,12 @@
291 291  
292 292  If the timeline is unlocked then you can instantly remove all the gaps between frames and push them up against each other by clicking the Operations button and choosing Remove Gaps Between Frames from the menu.
293 293  
296 +**Frame Inspector**
297 +
298 +[[image:lss-flowarm-inspector-frame.png]]
299 +
300 +If any adjustments are required on a particular joint (servo) this function allows you to manually change them. Click on the particular frame and the commands can be edited.
301 +
294 294  == Sequencer ==
295 295  
296 296  **Reverse Frames**
LSS-flowarm-30812.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.CBenson
Size
... ... @@ -1,1 +1,0 @@
1 -260.5 KB
Content
lss-flowarm-header.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.CBenson
Size
... ... @@ -1,1 +1,0 @@
1 -17.7 KB
Content
lss-flowarm-gripper-view.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +4.7 KB
Content
lss-flowarm-header.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +23.4 KB
Content
lss-flowarm-inspector-frame.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +3.1 KB
Content
lss-flowarm-inspector.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +1.9 KB
Content
lss-flowarm-left.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +11.2 KB
Content
lss-flowarm-offset-left.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +9.8 KB
Content
lss-flowarm-offset-top.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +7.0 KB
Content
lss-flowarm-top.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +7.1 KB
Content
lss-flowarm-wrist-view.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +3.6 KB
Content

Navigation

Copyright RobotShop 2018