Changes for page FlowArm LSS
Last modified by Eric Nantel on 2024/07/03 09:39
Change comment: There is no comment for this version
Summary
-
Page properties (2 modified, 0 added, 0 removed)
-
Attachments (0 modified, 1 added, 0 removed)
Details
- Page properties
-
- Author
-
... ... @@ -1,1 +1,1 @@ 1 -xwiki:XWiki. ENantel1 +xwiki:XWiki.CBenson - Content
-
... ... @@ -1,6 +1,6 @@ 1 1 [[image:LSS-FlowArm.png||width="350"]] 2 2 3 -[[ [[image:lynxmotion-wiki-attachments.WebHome@DownloadNow.png]]>>https://www.lynxmotion.com/tools/LSS_FlowArm.zip]]3 +[[image:wiki-download.png]] 4 4 5 5 **Page Contents** 6 6 ... ... @@ -28,7 +28,11 @@ 28 28 29 29 Before assembling the arm, each of the IDs assigned to the servos must correspond with what is needed in the software. 30 30 31 -{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-articulated-arm/lss-articulated-arm-servo-setup/WebHome/SESV2-LSS-ARTICULATED-ARM-IDS.PNG" width="350"/}} 31 +* Base: 1 32 +* Shoulder: 2 33 +* Elbow: 3 34 +* Wrist: 4 35 +* Gripper: 5 32 32 33 33 To do so, the [[LSS Configuration Software>>doc:lynxmotion-smart-servo.lss-configuration-software.WebHome]] is used. Follow the procedure outlined here: [[doc:lynxmotion-smart-servo.lss-configuration-software.lss-config-configure-ids.WebHome]] 34 34 ... ... @@ -36,13 +36,14 @@ 36 36 * Servos have been assembled in correct orientation (as per assembly manual) 37 37 * Servo offsets have been updated if necessary (see procedure below). 38 38 43 +The next important step is "STORE OFFSETS" explained below. 44 + 39 39 == Connecting via USB == 40 40 41 -The simplest way to connect is directly using the [[LSS-Adapter>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]](or anyRS232 to USBinterface). Here are the steps you need to follow in order to set this up. Follow the steps below:47 +The simplest way to connect is directly using an RS232 to USB cable. Here are the steps you need to follow in order to set this up. Follow the steps below: 42 42 43 43 1. Connect the USB cable to the LSS Adapter board on your robot 44 44 1. Plug the USB connector into the PC 45 -1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable 46 46 1. Connect the power to the LSS Adapter via the yellow XT60 plug 47 47 1. Power on the robot (On/Off switch) 48 48 1. Start the LSS FlowArm software ... ... @@ -51,7 +51,7 @@ 51 51 52 52 == Connecting via Bluetooth == 53 53 54 -If you have purchased a Bluetooth module which is in XBee format, ensure to have the right baudrate on your bluetooth adapter, the default is 115 200 for the LSS.59 +If you have purchased a Bluetooth module which is in XBee format, ensure 55 55 56 56 = Interface = 57 57
- wiki-download.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.CBenson - Size
-
... ... @@ -1,0 +1,1 @@ 1 +3.9 KB - Content