Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 1 removed)
  • lss-flowarm-inspector.png
  • LSS-flowarm-30812.jpg

Details

Page properties

Content

...	...	@@ -1,6 +1,6 @@
1		-{{lightbox image="LSS-FlowArm.png" width="400"/}}
	1	+[[image:LSS-FlowArm.png||width="350"]]
2	2
3		-[[[[image:lynxmotion-wiki-attachments.WebHome@DownloadNow.png]]>>https://www.lynxmotion.com/tools/LSS_FlowArm.zip]]
	3	+[[image:lynxmotion-wiki-attachments.WebHome@ComingSoon.jpg||alt="wiki-download.png"]]
4	4
5	5	**Page Contents**
6	6
...	...	@@ -28,7 +28,11 @@
28	28
29	29	Before assembling the arm, each of the IDs assigned to the servos must correspond with what is needed in the software.
30	30
31		-{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-articulated-arm/lss-articulated-arm-servo-setup/WebHome/SESV2-LSS-ARTICULATED-ARM-IDS.PNG" width="350"/}}
	31	+* Base: 1
	32	+* Shoulder: 2
	33	+* Elbow: 3
	34	+* Wrist: 4
	35	+* Gripper: 5
32	32
33	33	To do so, the [[LSS Configuration Software>>doc:lynxmotion-smart-servo.lss-configuration-software.WebHome]] is used. Follow the procedure outlined here: [[doc:lynxmotion-smart-servo.lss-configuration-software.lss-config-configure-ids.WebHome]]
34	34
...	...	@@ -36,22 +36,23 @@
36	36	* Servos have been assembled in correct orientation (as per assembly manual)
37	37	* Servo offsets have been updated if necessary (see procedure below).
38	38
	43	+The next important step is "STORE OFFSETS" explained below.
	44	+
39	39	== Connecting via USB ==
40	40
41		-The simplest way to connect is directly using the [[LSS-Adapter>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]] (or any RS232 to USB interface). Here are the steps you need to follow in order to set this up. Follow the steps below:
	47	+The simplest way to connect is directly using an RS232 to USB cable. Here are the steps you need to follow in order to set this up. Follow the steps below:
42	42
43	43	1. Connect the USB cable to the LSS Adapter board on your robot
44	44	1. Plug the USB connector into the PC
45		-1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable
46	46	1. Connect the power to the LSS Adapter via the yellow XT60 plug
47	47	1. Power on the robot (On/Off switch)
48	48	1. Start the LSS FlowArm software
49		-1. Select the appropriate COM port from the drop-down list & the baudrate (115200)
	54	+1. Select the appropriate COM port from the drop-down list
50	50	1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established.
51	51
52	52	== Connecting via Bluetooth ==
53	53
54		-If you have purchased a Bluetooth module which is in XBee format, ensure to have the right baudrate on your bluetooth adapter, the default is 115 200 for the LSS.
	59	+If you have purchased a Bluetooth module which is in XBee format, ensure
55	55
56	56	= Interface =
57	57
...	...	@@ -193,7 +193,6 @@
193	193	|(% style="width:257px" %)[[image:lss-flowarm-lock.jpg]]|(% style="width:306px" %)Lock |(% style="width:758px" %)Timeline locking
194	194	|(% style="width:257px" %)[[image:lss-flowarm-loop.jpg]]|(% style="width:306px" %)Repeat / Loop Pattern|(% style="width:758px" %)Play once or loop; Set the playback speed using the up and down arrows.
195	195	|(% style="width:257px" %)[[image:lss-flowarm-play.jpg]]|(% style="width:306px" %)Sequence Playback|(% style="width:758px" %)Restart sequence, play or stop
196		-|(% style="width:257px" %) |(% style="width:306px" %)Frame Inspector|(% style="width:758px" %)Allows to modify the values sent in a particular frame manually.
197	197
198	198	**Sequences**
199	199

lss-flowarm-inspector.png

Author

...	...	@@ -1,1 +1,0 @@
1		-xwiki:XWiki.ENantel

Size

...	...	@@ -1,1 +1,0 @@
1		-2.2 KB

Content

LSS-flowarm-30812.jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.CBenson

Size

...	...	@@ -1,0 +1,1 @@
	1	+260.5 KB

Content