Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 11 added, 1 removed)
  • lss-flowarm-header.jpg
  • lss-flowarm-data-log.png
  • lss-flowarm-gripper-view.png
  • lss-flowarm-header.png
  • lss-flowarm-inspector-frame.png
  • lss-flowarm-left.png
  • lss-flowarm-offset-left.png
  • lss-flowarm-offset-top.png
  • lss-flowarm-positioning.png
  • lss-flowarm-sequencer.png
  • lss-flowarm-top.png
  • lss-flowarm-wrist-view.png

Details

Page properties

Content

...	...	@@ -57,8 +57,12 @@
57	57
58	58	== Header ==
59	59
60		-[[image:lss-flowarm-header.jpg]]
	60	+[[image:lss-flowarm-header.png||alt="lss-flowarm-header"]]
61	61
	62	+**EMERGENCY STOP**
	63	+
	64	+At any given time you can click this button to stop the arm. This will send a "LIMP" command directly to all servos.
	65	+
62	62	**STORE OFFSETS**
63	63
64	64	The "STORE OFFSETS" button configures all of the servo offsets (this makes use of the CO command as part of the [[LSS Communication Protocol>>doc:lynxmotion-smart-servo.lss-communication-protocol.WebHome]]). Before pressing the button, orient the arm as shown below (with the gripper closed), and only then click the STORE OFFSETS button.
...	...	@@ -69,11 +69,12 @@
69	69	* Wrist servo along R axis (parallel to elbow to wrist)
70	70	* Gripper servo closed
71	71
72		-[[image:lss-flowarm-offsets.jpg]]
	76	+(% style="width:700px" %)
	77	+|(% style="text-align:center; vertical-align:middle" %)[[image:lss-flowarm-offset-left.png||alt="lss-flowarm-left.png" height="300" width="300"]]|(% style="text-align:center; vertical-align:middle" %)[[image:lss-flowarm-offset-top.png||alt="lss-flowarm-top.png" height="300" width="300"]]
73	73
74	74	**LIMP**
75	75
76		-Causes all servos to immediately go LIMP (i.e. lose torque). The arm will collapse. It's important to note that the software will not constantly query all servos for their position, and as such the virtual arm on screen will not update frequently if at all. If you want the virtual arm on screen to update as you move the real arm, use TEACH mode described below.
	81	+Causes all servos to slowly go LIMP (i.e. lose torque), gradually loosing torque until hitting the ground. It's important to note that the software will not constantly query all servos for their position, and as such the virtual arm on screen will not update frequently if at all. If you want the virtual arm on screen to update as you move the real arm, use TEACH mode described below.
77	77
78	78	**STOP**
79	79
...	...	@@ -118,13 +118,13 @@
118	118
119	119	The left view is a representation of the arm, where the orange circles represent the location of each axis of rotation. You can move the arm in this view by clicking on and dragging the wrist rotation servo.
120	120
121		-[[image:lss-flowarm-side-view.jpg]]
	126	+[[image:lss-flowarm-left.png||width="300"]]
122	122
123	123	**Top View**
124	124
125	125	The top view shows the arm top down. You can move the arm within this view by clicking on and dragging the wrist rotation servo.
126	126
127		-**[[image:lss-flowarm-top-view.jpg]]**
	132	+**[[image:lss-flowarm-top.png||width="300"]]**
128	128
129	129	=== Shortcuts ===
130	130
...	...	@@ -146,20 +146,15 @@
146	146
147	147	**Gripper**
148	148
149		-Assuming the gripper has been properly calibrated, The number below represents the opening at the tip. Fully closed should correspond to 0 degrees. In order to grasp an object, DO NOT have the servo rotate to a position which it cannot reach. In order to ensure the gripper servo does not go into error mode, the gripper should not exert much force on the object.
	154	+Assuming the gripper has been properly calibrated, The number below represents the opening at the tip. Fully closed should correspond to 0 degrees. We added a feature where the servo stop when it feel a current raising, this allows the user to ask for a full close and have a good grip on the item picked.
150	150
151		-1. Close the gripper to a position just slightly larger than the object
152		-1. Using the arrows, close the gripper until friction between the foam and the object prevent the object from falling out or moving.
153		-1. DO NOT apply too much pressure, or else the servo's current will spike and it will go into error mode and need to be reset.
154		-1. Use the last position as the "fully closed" position for the gripper for that object, in that specific orientation.
	156	+[[image:lss-flowarm-gripper-view.png||alt="lss-flowarm-gripper-view.jpg"]]
155	155
156		-[[image:lss-flowarm-gripper-view.jpg]]
157		-
158	158	**Wrist**
159	159
160	160	The wrist angle can be locked or unlocked. The field allows for user input (click the numbers) or fine adjustments using the arrows.
161	161
162		-[[image:lss-flowarm-wrist-view.jpg]]
	162	+[[image:lss-flowarm-wrist-view.png||alt="lss-flowarm-wrist-view.jpg"]]
163	163
164	164	**End Effector Position**
165	165
...	...	@@ -167,17 +167,17 @@
167	167
168	168	When in keyboard mode, there is an overlay indicating which keys do what motion.
169	169
170		-[[image:lss-flowarm-positioning.jpg]]
	170	+[[image:lss-flowarm-positioning.png||alt="lss-flowarm-positioning.jpg"]]
171	171
172	172	== **Data Log** ==
173	173
174	174	The optional Data log (normally hidden) can be toggled on or off and allows the user to see all commands being sent to and received from the smart servos. The data can be saved to a file in a Comma Separated Values (.csv) format.
175	175
176		-[[image:lss-flowarm-data-log.jpg]]
	176	+[[image:lss-flowarm-data-log.png||alt="lss-flowarm-data-log.jpg"]]
177	177
178	178	= Sequencer =
179	179
180		-[[image:lss-flowarm-sequencer.jpg]]
	180	+[[image:lss-flowarm-sequencer.png||alt="lss-flowarm-sequencer.jpg"]]
181	181
182	182	LSS FlowArm has a powerful pattern sequencer component (normally found only in the full version of FlowBotics Studio) that is used to create reusable patterns within minutes, instead of hours or days.
183	183
...	...	@@ -295,7 +295,10 @@
295	295
296	296	**Frame Inspector**
297	297
	298	+[[image:lss-flowarm-inspector-frame.png]]
298	298
	300	+If any adjustments are required on a particular joint (servo) this function allows you to manually change them. Click on the particular frame and the commands can be edited.
	301	+
299	299	== Sequencer ==
300	300
301	301	**Reverse Frames**

lss-flowarm-header.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-xwiki:XWiki.CBenson

Size

...	...	@@ -1,1 +1,0 @@
1		-17.7 KB

Content

lss-flowarm-data-log.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+10.8 KB

Content

lss-flowarm-gripper-view.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+4.7 KB

Content

lss-flowarm-header.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+23.4 KB

Content

lss-flowarm-inspector-frame.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+3.1 KB

Content

lss-flowarm-left.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+11.2 KB

Content

lss-flowarm-offset-left.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+9.8 KB

Content

lss-flowarm-offset-top.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+7.0 KB

Content

lss-flowarm-positioning.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.5 KB

Content

lss-flowarm-sequencer.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+11.9 KB

Content

lss-flowarm-top.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+7.1 KB

Content

lss-flowarm-wrist-view.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+3.6 KB

Content