Changes for page FlowArm LSS

Last modified by Eric Nantel on 2024/07/03 09:39
From version < 78.1 >
edited by Eric Nantel
on 2019/10/17 14:05
To version < 62.1 >
edited by Eric Nantel
on 2019/09/23 10:38
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,6 @@
1 -{{lightbox image="LSS-FlowArm.png" width="400"/}}
1 +[[image:LSS-FlowArm.png||width="350"]]
2 2  
3 -[[[[image:lynxmotion-wiki-attachments.WebHome@DownloadNow.png]]>>https://www.lynxmotion.com/tools/LSS_FlowArm.zip]]
3 +[[image:lynxmotion-wiki-attachments.WebHome@ComingSoon.jpg||alt="wiki-download.png"]]
4 4  
5 5  **Page Contents**
6 6  
... ... @@ -28,7 +28,11 @@
28 28  
29 29  Before assembling the arm, each of the IDs assigned to the servos must correspond with what is needed in the software.
30 30  
31 -{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-articulated-arm/lss-articulated-arm-servo-setup/WebHome/SESV2-LSS-ARTICULATED-ARM-IDS.PNG" width="350"/}}
31 +* Base: 1
32 +* Shoulder: 2
33 +* Elbow: 3
34 +* Wrist: 4
35 +* Gripper: 5
32 32  
33 33  To do so, the [[LSS Configuration Software>>doc:lynxmotion-smart-servo.lss-configuration-software.WebHome]] is used. Follow the procedure outlined here: [[doc:lynxmotion-smart-servo.lss-configuration-software.lss-config-configure-ids.WebHome]]
34 34  
... ... @@ -36,22 +36,23 @@
36 36  * Servos have been assembled in correct orientation (as per assembly manual)
37 37  * Servo offsets have been updated if necessary (see procedure below).
38 38  
43 +The next important step is "STORE OFFSETS" explained below.
44 +
39 39  == Connecting via USB ==
40 40  
41 -The simplest way to connect is directly using the [[LSS-Adapter>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]] (or any RS232 to USB interface). Here are the steps you need to follow in order to set this up. Follow the steps below:
47 +The simplest way to connect is directly using an RS232 to USB cable. Here are the steps you need to follow in order to set this up. Follow the steps below:
42 42  
43 43  1. Connect the USB cable to the LSS Adapter board on your robot
44 44  1. Plug the USB connector into the PC
45 -1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable
46 46  1. Connect the power to the LSS Adapter via the yellow XT60 plug
47 47  1. Power on the robot (On/Off switch)
48 48  1. Start the LSS FlowArm software
49 -1. Select the appropriate COM port from the drop-down list & the baudrate (115200)
54 +1. Select the appropriate COM port from the drop-down list
50 50  1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established.
51 51  
52 52  == Connecting via Bluetooth ==
53 53  
54 -If you have purchased a Bluetooth module which is in XBee format, ensure to have the right baudrate on your bluetooth adapter, the default is 115 200 for the LSS.
59 +If you have purchased a Bluetooth module which is in XBee format, ensure
55 55  
56 56  = Interface =
57 57  
... ... @@ -193,7 +193,6 @@
193 193  |(% style="width:257px" %)[[image:lss-flowarm-lock.jpg]]|(% style="width:306px" %)Lock |(% style="width:758px" %)Timeline locking
194 194  |(% style="width:257px" %)[[image:lss-flowarm-loop.jpg]]|(% style="width:306px" %)Repeat / Loop Pattern|(% style="width:758px" %)Play once or loop; Set the playback speed using the up and down arrows.
195 195  |(% style="width:257px" %)[[image:lss-flowarm-play.jpg]]|(% style="width:306px" %)Sequence Playback|(% style="width:758px" %)Restart sequence, play or stop
196 -|(% style="width:257px" %)[[image:lss-flowarm-inspector.png]]|(% style="width:306px" %)Frame Inspector|(% style="width:758px" %)Allows to modify the values sent in a particular frame manually.
197 197  
198 198  **Sequences**
199 199  
... ... @@ -293,12 +293,6 @@
293 293  
294 294  If the timeline is unlocked then you can instantly remove all the gaps between frames and push them up against each other by clicking the Operations button and choosing Remove Gaps Between Frames from the menu.
295 295  
296 -**Frame Inspector**
297 -
298 -[[image:lss-flowarm-inspector-frame.png]]
299 -
300 -If any adjustments are required on a particular joint (servo) this function allows you to manually change them. Click on the particular frame and the commands can be edited.
301 -
302 302  == Sequencer ==
303 303  
304 304  **Reverse Frames**
lss-flowarm-header.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -23.4 KB
Content
lss-flowarm-inspector-frame.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -3.1 KB
Content
lss-flowarm-inspector.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -1.9 KB
Content
LSS-flowarm-30812.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.CBenson
Size
... ... @@ -1,0 +1,1 @@
1 +260.5 KB
Content
wiki-download.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.CBenson
Size
... ... @@ -1,0 +1,1 @@
1 +3.9 KB
Content

Navigation

Copyright RobotShop 2018