Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -14,7 +14,7 @@
14	14	</ul>
15	15	<p><font face="Verdana" size="2">Note: Loctite / thread lock can be used on the construction of the aluminum components, though it is not necessary if the nuts are properly tightened. However, don't use them with Lexan or plastic, as they are not necessary and may cause damage.</font></p>
16	16	</td>
17		- <td align="center" valign="top" ><font face="Verdana" size="2"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5a-arm-assembly-instructions-rev-2-1/WebHome/al5a20.jpg" border="2" height="240" hspace="10" width="320"><br>
	17	+ <td align="center" valign="top" width="320"><font face="Verdana" size="2"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5a-arm-assembly-instructions-rev-2-1/WebHome/al5a20.jpg" border="2" height="240" hspace="10" width="320"><br>
18	18	<b>Image of complete arm (SSC-32 Shown).</b></font></td>
19	19	</tr>
20	20	<tr>
...	...	@@ -31,7 +31,7 @@
31	31	can be more difficult to remove. If you have trouble you can gently
32	32	scrape the cut edge, then use duct tape to lift the covering off.</font></p>
33	33	<p><font face="Verdana" size="2">For further information on
34		-lexan, see <a href="https://www.lynxmotion.com/images/html/infolexa.htm" target="_blank">this
	34	+lexan, see <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/support/polycarbonate-info-page/" target="_blank">this
35	35	page</a>.</font></p>
36	36	</td>
37	37	<td align="center" valign="top"><font face="Verdana" size="2"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5a-arm-assembly-instructions-rev-2-1/WebHome/lexan01.jpg" border="2" height="240" hspace="10" width="320"><br>
...	...	@@ -569,11 +569,11 @@
569	569	you have the SSC-32U (USB connector), please proceed with Step 21b. If
570	570	you have the SSC-32 (serial connector), we'll use LynxTerm to test the
571	571	servos and confirm that they're all plugged into the proper channels (</font><font face="Verdana" size="2">just as in the Base Assembly Instructions)</font><font face="Verdana" size="2">.
572		-If you have not done so before, download and install <a href="http://www.lynxmotion.com/p-567-free-download-lynxterm.aspx" target="_blank">LynxTerm v1.08</a> or higher. Connect the SSC-32 to
	572	+If you have not done so before, download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm</a>. Connect the SSC-32 to
573	573	the serial port and apply power. The green LED should light up and stay
574	574	on
575	575	until it receives a valid serial command. Run the LynxTerm program. If
576		-LynxTerm cannot connect, please consult the <a href="http://www.lynxmotion.net/viewtopic.php?t=4702" target="_blank">serial
	576	+LynxTerm cannot connect, please consult the <a href="https://community.robotshop.com/forum/t/serial-usb-to-serial-port-troubleshooting/17938" target="_blank">serial
577	577	and USB-to-serial troubleshooting guide</a>.<br>
578	578	<br>
579	579	</font><font face="Verdana" size="2">
...	...	@@ -602,7 +602,7 @@
602	602	</b></font><font face="Verdana" size="2">Just like in the base instructions, we will use the SSC-32 Servo
603	603	Sequencer Utility to test the servos and confirm they are all plugged
604	604	into their proper servo channels and oriented correctly. If not done so
605		-before, download and install the <a href="http://www.lynxmotion.com/p-895-free-download-ssc-32-servo-sequencer-utility-created-using-flowbotics-studio.aspx" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
	605	+before, download and install the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/ssc-32-sequencer/" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
606	606	cable and power the board using the on/off switch.</font><font face="Verdana" size="2"> Run
607	607	the program.<br>
608	608	<br>
...	...	@@ -616,7 +616,7 @@
616	616	plugged into the channels as listed in Table 21. Easy does it; this is
617	617	real time control, so be careful.<br>
618	618	<br>
619		-For more information, please consult the </font><a href="http://www.flowbotics.com/manuals/ssc-32_servo_sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a><font face="Verdana" size="2">. </font><br>
	619	+For more information, please consult the </font><a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/ssc-32-sequencer/WebHome/SSC32%20Servo%20Sequencer.pdf" target="_blank">SSC32 Servo Sequencer Guide</a><font face="Verdana" size="2">. </font><br>
620	620
621	621	<br>
622	622	<font face="Verdana" size="2"> </font></td>