Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -569,11 +569,11 @@
569	569	you have the SSC-32U (USB connector), please proceed with Step 21b. If
570	570	you have the SSC-32 (serial connector), we'll use LynxTerm to test the
571	571	servos and confirm that they're all plugged into the proper channels (</font><font face="Verdana" size="2">just as in the Base Assembly Instructions)</font><font face="Verdana" size="2">.
572		-If you have not done so before, download and install <a href="http://www.lynxmotion.com/p-567-free-download-lynxterm.aspx" target="_blank">LynxTerm v1.08</a> or higher. Connect the SSC-32 to
	572	+If you have not done so before, download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm. Connect the SSC-32 to
573	573	the serial port and apply power. The green LED should light up and stay
574	574	on
575	575	until it receives a valid serial command. Run the LynxTerm program. If
576		-LynxTerm cannot connect, please consult the <a href="http://www.lynxmotion.net/viewtopic.php?t=4702" target="_blank">serial
	576	+LynxTerm cannot connect, please consult the <a href="https://community.robotshop.com/forum/t/serial-usb-to-serial-port-troubleshooting/17938" target="_blank">serial
577	577	and USB-to-serial troubleshooting guide</a>.<br>
578	578	<br>
579	579	</font><font face="Verdana" size="2">
...	...	@@ -602,7 +602,7 @@
602	602	</b></font><font face="Verdana" size="2">Just like in the base instructions, we will use the SSC-32 Servo
603	603	Sequencer Utility to test the servos and confirm they are all plugged
604	604	into their proper servo channels and oriented correctly. If not done so
605		-before, download and install the <a href="http://www.lynxmotion.com/p-895-free-download-ssc-32-servo-sequencer-utility-created-using-flowbotics-studio.aspx" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
	605	+before, download and install the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/ssc-32-sequencer/" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
606	606	cable and power the board using the on/off switch.</font><font face="Verdana" size="2"> Run
607	607	the program.<br>
608	608	<br>
...	...	@@ -616,7 +616,7 @@
616	616	plugged into the channels as listed in Table 21. Easy does it; this is
617	617	real time control, so be careful.<br>
618	618	<br>
619		-For more information, please consult the </font><a href="http://www.flowbotics.com/manuals/ssc-32_servo_sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a><font face="Verdana" size="2">. </font><br>
	619	+For more information, please consult the </font><a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/ssc-32-sequencer/WebHome/SSC32%20Servo%20Sequencer.pdf" target="_blank">SSC32 Servo Sequencer Guide</a><font face="Verdana" size="2">. </font><br>
620	620
621	621	<br>
622	622	<font face="Verdana" size="2"> </font></td>