AL5A Arm Assembly Instructions Rev. 2.1

If you have not done so before, download and install <a href="http://www.lynxmotion.com/p-567-free-download-lynxterm.aspx" target="_blank">LynxTerm v1.08</a> or higher. Connect the SSC-32 to

591

the serial port and apply power. The green LED should light up and stay

592

on

593

until it receives a valid serial command. Run the LynxTerm program. If

594

LynxTerm cannot connect, please consult the <a href="http://www.lynxmotion.net/viewtopic.php?t=4702" target="_blank">serial

595

and USB-to-serial troubleshooting guide</a>.

596

597

598

Now test the servos and connections by selecting a channel, and moving

599

the servo carefully using the slider bar. Verify that the servos are

600

plugged into the channels as listed in Table 20. Easy does it; this is

601

real time control, so be careful! Select channels 0 through 4 one at a time and test that each works.

</td>

Figure 21a (Lynxterm).

</td>

</tr>

<tr>

</tr>

<tr>

<td style="vertical-align: top;">Step

619

21b (SSC-32U / Servo Utility).

620

Just like in the base instructions, we will use the SSC-32 Servo

621

Sequencer Utility to test the servos and confirm they are all plugged

622

into their proper servo channels and oriented correctly. If not done so

623

before, download and install the <a href="http://www.lynxmotion.com/p-895-free-download-ssc-32-servo-sequencer-utility-created-using-flowbotics-studio.aspx" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB

624

cable and power the board using the on/off switch. Run

625

the program.

626

627

The SSC-32U is shipped with a baud rate of 9600. Ensure the baud rate

628

towards the bottom right of the window is set to 9600 (not 115200). The

629

software should automatically detect which COM port is connected to the

630

SSC-32U, and have installed the <a href="http://www.ftdichip.com/Drivers/VCP.htm" target="_blank">FTDI

631

(USB to serial) drivers</a> automatically.

632

Ensure Servos 0 4 are checked off in the software (and therefore

633

accessible). You can now move the sliders to see each servo rotate. Verify that the servos are

634

plugged into the channels as listed in Table 21. Easy does it; this is

635

real time control, so be careful.

636

637

For more information, please consult the <a href="http://www.flowbotics.com/manuals/ssc-32_servo_sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a>.

</td>

Figure 21b (SSC-32 Utility).</td>

</tr>

<tr>

</td>

</td>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 22a (SSC-32 / Lynxterm).

653

Click on the "All = 1500" button in LynxTerm. This will command the

654

servos to hold center position. Your arm should look like Figure 22. If

655

any joint is off by more than 15°, then you may have made an error in

656

assembly.

657

658

If you did not purchase RIOS software, please proceed to step 27.

</td>

Figure 22.

</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td style="vertical-align: top;">Step 22b (SSC-32U / Servo Utility).

676

Click on the "Calibrate" button in the SSC-32 Servo Sequencer Utility.

677

A knob next to each servo will appear (figure 22b). This knob is used

678

to fine tune the servo's center position. The knob is not intended to

679

be rotated: click the knob you wish to rotate, keeping the mouse button

680

down, and drag up and down to rotate the knob. Do this for each servo

681

until the arm looks like figure 22, and angles are 90 and 180 degrees.

682

If

683

any joint is off by more than 15°, then you may have made an error in

684

assembly.

685

686

Once all servos have been properly positioned, click the icon

687

"Calibrate" once again, and the offset values will be stored on the

688

SSC-32 / SSC-32U.

689

690

If you did not purchase the RIOS software, please proceed to step 27.</td>

691

692

693

Figure 22b (SSC-32 Utility).</td>

</tr>

<tr>

</td>

</td>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 23 (RIOS Users Only).

703

To use the RIOS Arm control software, you need to make one

704

minor modification. Remove the servo horn screw from the elbow servo.

705

Pull the servo horn off the servo, lift the arm two 'clicks' (30°) at

706

the elbow and reattach the servo horn and screw. Note, the Hitec spline

707

has 24 grooves, so each groove is 15°.</td>

Figure 23.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 24 (RIOS Users Only).

716

At this point the arms is assembled and tested using LynxTerm. If your

717

robot came with RIOS, we can now install RIOS and calibrate the arm to

718

the software. For those using a different program such as FlowBotics or

719

FlowStone, refer to the software's user guide. Use the RIOS Help File

720

to calibrate and use the arm.

721

Install RIOS, following the

722

on-screen installation prompts. The serial number is on the back of the

723

CD sleeve.

724

Use the RIOS Help File to

725

calibrate and use the arm, following Steps 1-7. When you get to Step 8

726

in the help file, please use the following instructions instead. Click

727

on the "Arm" button, then click on the "Arm" button in the "Arm size"

728

section, and then click on the AL5A arm image on the popup screen.

729

Please take the time to do an

730

accurate calibration. The performance of the arm will only be as good

731

as the calibration. If the on screen virtual arm does not match the

732

real arm this is a sign of an inaccurate calibration. After calibration

733

please study the RIOS manual carefully to learn how to store and

734

playback sequences for the arm.

</td>

Figure 24 (RIOS).

</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 25 (RIOS Users Only).

747

To calibrate the arm's shoulder servo, click the "SSC-32" button.</td>

Figure 25 (RIOS).

</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 26 (RIOS Users Only).

760

Select the Shoulder, servo #2. Move the shoulder slider up to move the

761

shoulder forward so that it looks like Figure 27-2. Set the Min Deg

762

angle -90°. Right click on the slider to set this as the Min Position.

763

Now the servo will not go past this value, and the program now knows

764

this value is exactly 90° from centered.

765

Now move the slider down to move

766

the shoulder backward so that it looks like Figure 27-3. Set the Max

767

Deg angle to 45°. Right click on the slider to set this as the Max

768

Position. Now the servo will not go past this value, and the program

769

now knows this value is exactly 45° from centered.

770

The next step is to read and

771

study the RIOS users guide. It is accessible by clicking on the help

772

icon on the main screen or by navigating to the install directory

773

(c:\Program Files\RIOS_SSC-32\) and opening the Help.pdf file. This

774

manual explains in great detail how to use the arm.

</td>

Figure 26-1 (RIOS).

</td>

</tr>

<tr>

</tr>

<tr>

Figure 26-2.

</td>

Figure 26-3.

</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 27.

801

To connect springs for load-balancing, replace the servo

802

attachment hardware in the locations shown, following the diagrams

803

below. Hook the springs together after they're secured.

</td>

Figure 27.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" width="50%">Step 28.

816

The arm assembly is complete. The arm is robust mechanically,

817

but the servos can be damaged by improper use. An example would be if

818

the arm was told to move to an unobtainable position, like the surface

819

the arm is mounted to, or by crashing the arm into itself, or other

820

objects. The elbow servo is the most vulnerable because it holds the

821

entire weight of the forearm. Load balancing springs should be added to

822

reduce some of this load.

823

824

If you purchased FlowBotics Studio,

825

FlowStone or FlowArm, you can proceed with the instruction guide(s)

826

associated with those programs.

People do not

like holding heavy objects with their arms outstretched in front of

831

them. Servo based robot arms don't like it much either. Remember, the

832

most important rule for servo based robot arms: Park the arm when not

833

in motion! When it's moving or at rest it's usually ok. When it's

834

holding an object it should do so for the minimum amount of time

835

required to do the job. You can always touch the servo case to see if

it's getting hot.

</td>

</td>

</tr>

</tbody>

</table>

Wiki source code of AL5A Arm Assembly Instructions Rev. 2.1