Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -46,7 +46,7 @@
46	46	can be more difficult to remove. If you have trouble you can gently
47	47	scrape the cut edge, then use duct tape to lift the covering off.</font></p>
48	48	<p><font face="Verdana" size="2">For further information on
49		-lexan, see <a href="https://www.lynxmotion.com/images/html/infolexa.htm" target="_blank">this
	49	+lexan, see <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/support/polycarbonate-info-page/" target="_blank">this
50	50	page</a>.</font></p>
51	51	</td>
52	52	<td align="center" valign="top" ><font face="Verdana" size="2"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5d-arm-rev-2-1/WebHome/lexan01.jpg" border="2" height="240" hspace="10" ></font><br>
...	...	@@ -631,11 +631,11 @@
631	631	If you have the SSC-32 (serial connector), we'll use LynxTerm to test
632	632	the
633	633	servos and confirm that they're all plugged into the proper channels (</font><font face="Verdana" size="2">just as in the Base Assembly Instructions)</font><font face="Verdana" size="2">.
634		-If you have not done so before, download and install <a href="https://www.lynxmotion.com/showproduct.aspx?productID=567&amp;CategoryID=15#downloads" target="_blank">LynxTerm v1.08</a> or higher. Connect the SSC-32 to
	634	+If you have not done so before, download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm</a>. Connect the SSC-32 to
635	635	the serial port and apply power. The green LED should light up and stay
636	636	on
637	637	until it receives a valid serial command. Run the LynxTerm program. If
638		-LynxTerm cannot connect, please consult the <a href="http://www.lynxmotion.net/viewtopic.php?t=4702" target="_blank">serial
	638	+LynxTerm cannot connect, please consult the <a href="https://community.robotshop.com/forum/t/serial-usb-to-serial-port-troubleshooting/17938" target="_blank">serial
639	639	and USB-to-serial troubleshooting guide</a>.<br>
640	640	<br>
641	641	</font><font face="Verdana" size="2">Now test the servos and
...	...	@@ -660,7 +660,7 @@
660	660	Servo
661	661	Sequencer Utility to test the servos and confirm they are all plugged
662	662	into their proper servo channels and oriented correctly. If not done so
663		-before, download and install the <a href="http://www.lynxmotion.com/p-895-free-download-ssc-32-servo-sequencer-utility-created-using-flowbotics-studio.aspx" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
	663	+before, download and install the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/ssc-32-sequencer/" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
664	664	cable and power the board using the on/off switch.</font><font face="Verdana" size="2"> Run
665	665	the program.<br>
666	666	<br>
...	...	@@ -677,7 +677,7 @@
677	677	plugged into the channels as listed in Table 21. Easy does it; this is
678	678	real time control, so be careful.<br>
679	679	<br>
680		-For more information, please consult the <a href="http://www.flowbotics.com/manuals/ssc-32_servo_sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a>. </font><br>
	680	+For more information, please consult the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/ssc-32-sequencer/WebHome/SSC32%20Servo%20Sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a>. </font><br>
681	681	<br>
682	682	<br>
683	683	</td>