Last modified by Eric Nantel on 2024/08/07 14:28
From version < 12.1 >
edited by Eric Nantel
on 2019/10/31 09:50
To version < 27.1 >
edited by Eric Nantel
on 2019/11/01 09:52
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,62 +1,22 @@
1 -{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/ses-sabertooth-rlk-top.PNG" height="300"/}}
1 +
2 2  
3 -
4 4  (% style="width:1000px" %)
5 -|(% colspan="2" %)**Step 1.**
4 +|(% colspan="2" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/ses-sabertooth-rlk-top.PNG"/}}
5 +|(% colspan="2" %)**Step 1 - Sabertooth Setup**
6 6  |(% style="width:300px" %)(((
7 -
7 +[[image:dip-switch-example.jpg]]
8 8  )))|(((
9 -The Sabertooth 2X10 RC has a feature called battery elimination circuit (BEC) that provides power to the RC receiver. It can provide enough current to power the receiver alone, but not if servos are used. In order to provide enough power for the receiver and the servos attached to it, we need to add a separate battery pack. In addition, we need to bypass the Sabertooth's BEC to prevent it from interfering with the battery pack.
9 +The most important thing to set for your Sabertooth is the dip-switches that enable/disable different modes on the board.
10 10  
11 -Use an exacto knife to **carefully** pry the black tab up and slip the red wire out of the black housing as shown in Figure 1.
12 12  
13 -Bend the red wires up and use electrical tape to cover them as shown. This will prevent accidental shorts.
14 -)))
15 -|(% colspan="2" %)**Step 2.**
16 -|(((
17 -{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm03.jpg"/}}
18 -)))|(((
19 -Plug the Sabertooth into the receiver as shown. Make sure the yellow wires are toward the middle of the receiver. On some versions, there are two connections marked "AILE". Use the slot between THRO and ELEV for CH 1.
12 +Depending on your version of the Sabertooth you will have to set the dip-switches differently so we suggest you to have a look at the different user manuals here:
20 20  
21 -|(% style="text-align:center" %)**Sabertooth**|(% style="text-align:center" %)**Receiver**
22 -|(% style="text-align:center" %)CH1 / Throttle|(% style="text-align:center" %)CH-1
23 -|(% style="text-align:center" %)CH2 / Steering|(% style="text-align:center" %)CH-2
14 +* [[Sabertooth 2x5 RC>>https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/Sabertooth2X5RCQuickStart.pdf]]
15 +* [[Sabertooth 2x5>>https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/Sabertooth2X5QuickStart.pdf]]
16 +* [[Sabertooth 2x12 RC>>https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/Sabertooth2X12RCQuickStart.pdf]]
17 +* [[Sabertooth 2x12>>https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/Sabertooth2X12QuickStart.pdf]]
24 24  )))
25 -|(% colspan="2" %)**Step 3.**
26 -|(((
27 -
28 -)))|
29 -|(% colspan="2" style="text-align:center" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/ses-sabertooth-rlk-wiring.PNG"/}}
30 -|(% colspan="2" %)**Step 4.**
31 -|(((
32 -
33 -)))|
34 -|(% colspan="2" %)**Step 5.**
35 -|(((
36 -
37 -
38 -Make sure your Sabertooth's dip switches are in the default positions, as shown in Figure 5. It would be a good idea to read the [[Sabertooth manual>>url:http://www.lynxmotion.com/ViewPage.aspx?ContentCode=electronics&CategoryID=70#moto]] to familiarize yourself with the different settings. With the default settings, you can now control the rover although the controls will be reversed. This will be corrected later.
39 -)))|{{lightbox image="http://www.lynxmotion.com/images/jpg/sbrtooth.jpg"/}}
40 -|**Step 6. (Optional Pan and Tilt)**
41 -If you are not installing a Pan and Tilt you can skip down to step 8, ignoring this step. Punch the cutout out of the top panel.|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm05.jpg"/}}
42 -|(((
43 -**Step 7. (Optional Pan and Tilt)**
44 -
45 -Create a pan and tilt. Detailed instructions can be found [[here>>url:http://www.lynxmotion.com/images/html/build153.htm]]. Insert the bottom servo into the top panel and secure with 3mm hardware.
46 -)))|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm09.jpg"/}}
47 -|(((
48 -**Step 8.**
49 -
50 -To set the controls to behave normally, you must adjust the servo option switches. They are located on the front of the remote. Set them as listed in Table 8.
51 -)))|(((
52 -|Channels|Function|NOR/REV
53 -|THR| |
54 -| | |
55 -| | |
56 -| | |
57 -| | |
58 -
59 -
19 +|(% colspan="2" %)**Step 2 - Wiring**
20 +|(% colspan="2" %)(((
21 +{{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/SES%20V1%20Robots/ses-v1-wheeled-tracked/ses-v1-rc-tutorial/WebHome/ses-sabertooth-rlk-wiring.PNG"/}}
60 60  )))
61 -|**Step 9.**
62 -Refer to Figure 9 for information on controlling the robot.|(% colspan="1" style="text-align:center" %){{lightbox image="http://www.lynxmotion.com/images/jpg/rccont.jpg"/}}
Sabertooth2X12QuickStart.pdf
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +660.7 KB
Content
Sabertooth2X12RCQuickStart.pdf
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +80.1 KB
Content
Sabertooth2X5QuickStart.pdf
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +310.3 KB
Content
Sabertooth2X5RCQuickStart.pdf
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +238.4 KB
Content
dip-switch-example.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +7.9 KB
Content
Copyright RobotShop 2018