Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -20,14 +20,44 @@
20	20	|(% style="text-align:center" %)CH1 / Throttle|(% style="text-align:center" %)CH-1
21	21	|(% style="text-align:center" %)CH2 / Steering|(% style="text-align:center" %)CH-2
22	22	)))|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm03.jpg"/}}
23		-| |{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/rovsch03.png"/}}
24		-|(% style="text-align:center" %) |(% colspan="1" style="text-align:center" %){{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/rovsch01.png"/}}
25		-| |{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm01.jpg"/}}
26		-| |{{lightbox image="http://www.lynxmotion.com/images/jpg/sbrtooth.jpg"/}}
27		-| |{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm05.jpg"/}}
28		-| |{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm09.jpg"/}}
29		-| |
30		-| |
31		-|(% style="text-align:center" %) |(% colspan="1" style="text-align:center" %){{lightbox image="http://www.lynxmotion.com/images/jpg/rccont.jpg"/}}
	23	+|(((
	24	+**Step 3.**
32	32
	26	+Solder the BATC-01 cable to the WH-04 and cover the bare wires with heat shrink or electrical tape. This will allow you to use our rechargeable 6.0vdc batteries for the receiver and servos. Attach the switch to any of the holes in the top panel of the chassis. Plug the battery's wiring harness from the radio into the receiver as shown. Make sure the black wire is on the outside of the receiver. This is shown in the schematic below.
	27	+)))|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/rovsch03.png"/}}
	28	+|(% colspan="2" style="text-align:center" %){{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/rovsch01.png"/}}
	29	+|(((
	30	+**Step 4.**
	31	+
	32	+Bind the transmitter to the receiver. Refer to the Spektrum manual for detailed instructions.
	33	+)))|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm01.jpg"/}}
	34	+|(((
	35	+**Step 5.**
	36	+
	37	+Make sure your Sabertooth's dip switches are in the default positions, as shown in Figure 5. It would be a good idea to read the [[Sabertooth manual>>url:http://www.lynxmotion.com/ViewPage.aspx?ContentCode=electronics&CategoryID=70#moto]] to familiarize yourself with the different settings. With the default settings, you can now control the rover although the controls will be reversed. This will be corrected later.
	38	+)))|{{lightbox image="http://www.lynxmotion.com/images/jpg/sbrtooth.jpg"/}}
	39	+|**Step 6. (Optional Pan and Tilt)**
	40	+If you are not installing a Pan and Tilt you can skip down to step 8, ignoring this step. Punch the cutout out of the top panel.|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm05.jpg"/}}
	41	+|(((
	42	+**Step 7. (Optional Pan and Tilt)**
	43	+
	44	+Create a pan and tilt. Detailed instructions can be found [[here>>url:http://www.lynxmotion.com/images/html/build153.htm]]. Insert the bottom servo into the top panel and secure with 3mm hardware.
	45	+)))|{{lightbox image="http://www.lynxmotion.com/images/assembly/a4wd1rc2/assm09.jpg"/}}
	46	+|(((
	47	+**Step 8.**
	48	+
	49	+To set the controls to behave normally, you must adjust the servo option switches. They are located on the front of the remote. Set them as listed in Table 8.
	50	+)))|(((
	51	+|Channels|Function|NOR/REV
	52	+|THR| |
	53	+| | |
	54	+| | |
	55	+| | |
	56	+| | |
	57	+
33	33
	59	+)))
	60	+|**Step 9.**
	61	+Refer to Figure 9 for information on controlling the robot.|(% colspan="1" style="text-align:center" %){{lightbox image="http://www.lynxmotion.com/images/jpg/rccont.jpg"/}}
	62	+
	63	+