LSS-P - Electrical

**Page Contents**

= Typical Connections =

In order to daisy chain one servo to the next (serial mode only), rollover serial cables are used. Although the wires are straight, one connector must be rotated 180 degrees with respect to the other.

10

11

|(% style="text-align:center; width:350px" %)**Serial Single**|(% style="text-align:center; width:350px" %)**Serial Multiples**

12

|(% style="width:350px" %)(((

13

14

)))|(% style="width:350px" %)(((

)))

= Wiring Pinout =

|(% colspan="3" style="width:350px" %)**CAN Bus**

21

|(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**

22

|(% rowspan="3" style="width:350px" %)(((

23

24

)))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)(((

25

**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin

26

)))

27

|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)(((

28

**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.

29

)))

30

|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").

31

|(% colspan="3" style="width:350px" %)**Power**

32

|(% colspan="1" rowspan="2" style="width:350px" %)(((

33

34

)))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**:

35

|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:

Wiki source code of LSS-P - Electrical

Navigation

Recently Visited

1	{{warningBox warningText="More information coming soon"/}}
2
3	Page Contents
4
5	{{toc/}}
6
7	= Typical Connections =
8
9	In order to daisy chain one servo to the next (serial mode only), rollover serial cables are used. Although the wires are straight, one connector must be rotated 180 degrees with respect to the other.
10
11	\|(% style="text-align:center; width:350px" %)Serial Single\|(% style="text-align:center; width:350px" %)Serial Multiples
12	\|(% style="width:350px" %)(((
13
14	)))\|(% style="width:350px" %)(((
15
16	)))
17
18	= Wiring Pinout =
19
20	\|(% colspan="3" style="width:350px" %)CAN Bus
21	\|(% style="width:350px" %) \|(% style="text-align:left; vertical-align:middle; width:35px" %) \|(% style="text-align:center; vertical-align:middle" %)Serial Mode
22	\|(% rowspan="3" style="width:350px" %)(((
23
24	)))\|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]\|(% style="text-align:left; vertical-align:middle" %)(((
25	Servo Rx: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
26	)))
27	\|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]\|\|alt="SQUARE-Yellow.png"]]\|(% style="text-align:left; vertical-align:middle" %)(((
28	Servo Tx: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
29	)))
30	\|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]\|\|alt="SQUARE-Yellow.png"]]\|(% style="text-align:left; vertical-align:middle" %)Ground (GND): This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
31	\|(% colspan="3" style="width:350px" %)Power
32	\|(% colspan="1" rowspan="2" style="width:350px" %)(((
33
34	)))\|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]\|\|alt="SQUARE-Yellow.png"]]\|(% style="text-align:left; vertical-align:middle" %)Servo Vcc:
35	\|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]\|\|alt="SQUARE-Yellow.png"]]\|(% style="text-align:left; vertical-align:middle" %)Ground (GND):