02 - Center Frame

Last modified by Eric Nantel on 2021/08/06 12:23

MES - Center Frame

Center Frame - MES

Step 1/14

1x MES-F-BCP

Bottom Center Plate

4x MES-F-LSP

Landing Support

4x MES-F-LC

Landing Clip

2x AHS-12-BA

1" Standoff

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 2/14

8x AHS-12-BA

1" Standoff

8x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 3/14

4x AHS-13-BA

1.5" Standoff

4x SHS-01

4-40 x 1/4"

Power Distribution Board

Optional

1x MES-PDB

Power Distribution Board

4x AHS-10-BA

1/4" Standoff

4x AHS-13-BA

1.5" Standoff

4x SHS-05

4-40 3/4"

Comments:If you have a Lynxmotion MES-PDB or other 45mm compatible power distribution board, skip step 03 and follow this step. Note that the 1.5" standoffs can be substituted for 1" if needed.

Quick Release Mounting

Optional

4x MES-F-GS

Grommet Support

4x AHS-11

1/2" Standoff

8x RHG-01

Hole Grommet

8x SHS-01

4-40 x 1/4"

Comments:If you will be using the quick release system, proceed with the installation of the mounting system here.

Center Frame - MES

Step 4/14

4x MES-F-AC

Arm Clip

4x AHS-12-BA

1" Standoff

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 5/14

4x UAV-Clamp

Tube Clamp

8x SHS-01

4-40 x 1/4"

Step 6 will require you to choose between 3 different main configurations:
6.1 - Quadcopter with front being in middle of two arm
6.2 - Y4 or Y6 Two arm front and one back either 4 or 6 motors
6.3 - HEX with an arm in the middle front

Center Frame - MES (Config QUADX)

Step 6.1/14

4x Corner Arm

MES Arm Assembly

Center Frame - MES (Config Y4 / Y6)

Step 6.2/14

4x Corner Arm

MES Arm Assembly

1x Center Arm

MES Arm Assembly

1x CF-TUBE

50mm Tube

Center Frame - MES (Config HEX)

Step 6.3/14

4x Corner Arm

MES Arm Assembly

2x Center Arm

MES Arm Assembly

Center Frame - MES

Step 7/14

4x BB-03

8 x 3mm Bearing

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 8/14

1x MES-F-TCP

Top Center Plate

4x UAV-Clamp

Tube Clamp

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 9/14

8x SHS-05

4-40 x 3/4"

Center Frame - MES

Step 10/14

4x MES-F-TBP

Tower Bottom Plate

2x MES-F-TIP

Tower Insert Plate

4x AHS-12-BA

1" Standoff

8x SHS-01

4-40 x 1/4"

Comments:Both sides of the frame need to be populated

Tower Battery Mount

Optional

1x MES-F-BP

Battery Plate

1x MES-F-BF

Battery Foam

2x AHS-11-BA

1/2" Standoff

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 11/14

2x MES-F-TTP

Tower Top Plate

2x AHS-12-BA

1" Standoff

4x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 12/14

8x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 13/14

4x MES-F-AC

Arm Clip

4x BB-03

8 x 3mm Bearing

8x SHS-01

4-40 x 1/4"

Center Frame - MES

Step 14/14

1x MES-F-FCP

Flight Controller Plate

1x MES-F-RP

Receiver Plate

1x MES-F-AP

Antenna Plate

1x UAV-FC

Flight Controller

4x SHS-01

4-40 x 1/4"

MES - Center Frame

Tags:

Created by Eric Nantel on 2021/08/06 09:45