T-Hex 3DoF Leg Assembly Instructions

Last modified by Eric Nantel on 2023/01/26 13:11

3 DOF T-HEX Leg Assembly Instructions.

Updated 11/11/2010

Safety first! Wear eye protection and never touch a powered robot!

Important! If you are building legs for the T-HEX robot, you will need to build three right legs (following the pictures on the right), and three left legs (by following the pictures on the left)! If you are building legs for your own creation, feel free to choose your own style.


Image of completed Right (robot's right) leg.
 

Figure 1. (Left Leg)

Step 1.
Attach a Tubing Connector Hub to an "L" bracket as shown, using two 2-56 x .250 screws and 2-56 nuts. You will need to make six of these.

12 x 12 x

Figure 1. (Right Leg)
 

Figure 2. (Left Leg)

Step 2.
Attach the other side of the "L" connector bracket to the Multi-Purpose bracket as shown, using two 2-56 x .250 screws and 2-56 nuts. Make three of each.

12 x 12 x

Figure 2. (Right Leg)
 

Figure 3. (Left Leg)

Step 3.
Connect a 1.5" tube to each hub using a 4-40 x .250" screw.

6 x  
 

Figure 3. (Right Leg)


Figure 4. (Left Leg)

Step 4.
Attach a long "C" bracket to an offset "C" bracket as shown, using two 2-56 x .250 screws and 2-56 nuts. Create six of these.

12 x 12 x


Figure 4. (Right Leg)
 

Figure 5. (Left Leg)

Step 5.
Attach the offset "C" bracket to the Multi-Purpose bracket as shown. See the diagram below for detailed information. You will end up with three of each assembly.


Figure 5-1.


Figure 5. (Right Leg)
 

Figure 6. (Left Leg)

Step 6.
Attach a ball bearing to the Multi-Purpose bracket as shown. See the diagram below for detailed information. Make three of each.


Figure 6-1.


Figure 6. (Right Leg)
 

Figure 7. (Left Leg)

Step 7. (Front and Middle Legs)
Attach the two multi-purpose brackets as shown, using two 2-56 x .250" screws and 2-56 nuts. Make two for each side. 

8 x 8 x

 


Figure 7. (Right Leg)


Figure 8. (Left Leg)
Step 8. (Front and Middle Legs)
Attach the "C" bracket to the Multi-Purpose bracket as shown. See the diagram below for detailed information. Make two of each.


Figure 8-1.


Figure 8. (Right Leg)
 

Figure 9. (Left Leg)

Step 9. (Front and Middle Legs)
Install the servos as shown, using the included 3mm hardware, and #2 tapping screws.

12 x 48 x

Figure 9. (Right Leg)
 

Figure 10. (Left Leg)

Step 10. (Rear Legs)
Attach the two multi-purpose brackets as shown, using two 2-56 x .250" screws and 2-56 nuts. 

8 x 8 x

 


Figure 10. (Right Leg)
 

Figure 11. (Left Leg)
Step 11. (Rear Legs)
Attach the "C" bracket to the Multi-Purpose bracket as shown. See the diagram below for detailed information.


Figure 11-1.


Figure 11. (Right Leg)


Figure 12. (Left Leg)

Step 12. (Rear Legs)
Install the servos as shown, using the included 3mm hardware, and #2 tapping screws.

8 x 24 x

Figure 12. (Right Leg)
 

Figure 13. (Left Leg)
Step 13. (All Legs)
Slide a rubber foot over the over the end of each 1.5" tube, and you're finished!

Figure 13. (Right Leg)
Tags:
Created by Eric Nantel on 2023/01/26 12:50
Copyright RobotShop 2018