AL5A Arm Assembly Instructions Rev. 2.1

1

2

3

<tbody>

4

<tr>

5

<td align="left" valign="top">AL5A Arm Assembly Instructions Rev. 2.1.

6

Updated Dec 2014

7

Safety first! Wear eye protection and never touch a powered robot!

8

This guide shows how to assemble the AL5A arm with either the SSC-32 or the SSC-32U servo controller. Take note of which version you have and follow each step accordingly, as the connections and configuration are different. Calibration of the arm is done using one of the following software:

9

<ul>

10

<li>SSC-32 Servo Sequencer Utility

11

</li>

12

<li>RIOS (purchased separately or as part of a kit)</li>

13

<li>Lynxterm (Legacy software)</li>

14

</ul>

15

Note: Loctite / thread lock can be used on the construction of the aluminum components, though it is not necessary if the nuts are properly tightened. However, don't use them with Lexan or plastic, as they are not necessary and may cause damage.

16

</td>

17

18

Image of complete arm (SSC-32 Shown).</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Lexan Preparation.

25

The lexan pieces have a protective covering that needs to be

26

removed before assembly. When the laser cuts, the covering melts into

27

the cut edge which can make removal difficult. If you gently scrape the

28

cut edge with a flat blade screwdriver, the covering can easily be

29

lifted and peeled off.

30

On smaller pieces the coverings

31

can be more difficult to remove. If you have trouble you can gently

32

scrape the cut edge, then use duct tape to lift the covering off.

33

For further information on

34

lexan, see <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/support/polycarbonate-info-page/" target="_blank">this

page</a>.

</td>

Lexan Preparation.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 1.

45

Connect the standard "C" bracket to the large "C" bracket as shown. Use two 2-56

46

x 1/4" screws and 2-56 nuts.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 1.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 2.

70

Install the mechanical dampening panels as shown. Use four 2-56 x 1/4 inch

71

machine screws. Be sure to add the discs to the correct side and ensure the protective covering has been

72

removed from the Lexan parts.

73

Press down when screwing to ensure there is no gap between the Lexan

74

and the aluminum, as the screw will be threading the Lexan.

</td>

Figure 2.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 3.

86

Insert the 4-40 x .5" Phillips head screw through the hole in

87

the multi-purpose bracket as shown. Secure with a steel nut.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 3.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 4.

110

Slide the large "C" bracket end of the bracket assembly over

111

the screw as shown, and secure with a nylon insert lock nut. The amount

112

of friction can be adjusted by tightening or loosening the lock nut.

113

Start with the nut loose, and if the arm seems to wobble a bit, you can

114

tighten this joint to correct the wobble. Caution

115

- don't over-tighten this! If the arm is operated with the mechanical

116

dampeners too tight, the servo WILL heat up and CAN be damaged!

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 4.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" >Step

140

5.

141

Figure 5 shows a typical mega-size servo with its default

142

servo horn at center position. You will need to replace this black

143

servo horn on the 755 servo with the round nylon servo horn included with the hardware bag.

144

145

Remove

146

the servo horn screw,

147

being careful to not rotate the servo horn itself. Pull the servo horn

148

off, then press the nylon servo horn in place, as close to the

149

alignment shown as possible. Replace the servo horn screw. Make sure

150

your large servo looks like figure 5. The arrows in the image point to

151

the screw holes you will

use.

</td>

Figure 5.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 6.

162

Attach the HS-755HB servo to the base bracket as shown using

163

the 3mm hardware; follow the diagram below. Use two #2 x 1/4" tapping

164

screws to secure the bracket to the servo horn. Route the shoulder

165

servo wires underneath the servo. Plug the servo into channel 1 on the

166

SSC-32. Carefully rotate the base to an extreme, and use a wire tie to

167

take up the slack in the servo cable.

<tbody>

<tr>

</tr>

<tr>

</tr>

<tr>

</tr>

<tr>

</td>

</tr>

</tbody>

</table>

</td>

Figure 6.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 7.

199

Attach two of the tubing connector hubs to the short side of

200

the "L" brackets, using four 2-56 x .250 screws and 2-56 nuts. Orientation is important; the hole in the tube should be as shown, so

201

the tube will line up as in figure 8.

<tbody>

<tr>

<td >4 x (two each)

</td>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 7.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 8.

226

Connect the hubs to the 1.50" tube using two 4-40 x .250"

227

screws. Tighten these down tightly.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 8.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 9.

250

Attach each of the ends of the tubing structure to two standard sized Multi-Purpose brackets as

251

shown, using four 2-56 x .250 screws and 2-56 nuts.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 9.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 10.

275

Insert the 4-40 x .5" Phillips head screw through the hole in the

276

multi-purpose bracket as shown. Secure with a steel nut.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 10.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 11.

299

Slide the screw on the forearm assembly through the dampening

300

discs as shown, and secure with a nylon insert lock nut. The amount of

301

friction can be adjusted by tightening or loosening the lock nut. Start

302

with the nut loose, and if the arm seems to wobble a bit, you can

303

tighten this joint to correct the wobble. Caution

304

- don't over-tighten this! If the arm is operated with the mechanical

305

dampeners too tight, the servo WILL heat up and CAN be damaged!

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 11.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" >Step

328

12.

329

Figure 12 illustrates a typical standard-size servo with its

330

output horn (the round white part) at center position. Make sure your

331

servo looks like the image. The arrows in the image point to the screw

332

holes you will use.</td>

Figure 12.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 13.

342

Attach the HS-645HB elbow servo to the bracket as shown using the 3mm

343

hardware; follow the diagram below. Use two #2 x 1/4" tapping screws to

344

secure the bracket to the servo horn. Route the shoulder servo wires

345

over the servo. Plug the servo into channel 2 on the SSC-32.

<tbody>

<tr>

</tr>

<tr>

</tr>

<tr>

</tr>

<tr>

</td>

</tr>

</tbody>

</table>

</td>

Figure 13.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 14.

376

Attach the Little Gripper connector to the Short "C" bracket

377

using two 2-56 x .250" screws and 2-56 nuts.

<tbody>

<tr>

</tr>

<tr>

</tr>

</tbody>

</table>

</td>

Figure 14.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 15.

401

Attach the short "C" bracket to the other Multi-purpose

bracket as shown.

Figure 15-1.

</td>

Figure 15-2.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 16.

414

Attach the HS-422 wrist servo to the bracket as shown using the 3mm hardware; follow the

415

diagram below. Use two #2 x 1/4" tapping screws to secure the bracket

416

to the servo horn. Route the shoulder servo wires over the servo.

<tbody>

<tr>

</tr>

<tr>

</tr>

<tr>

</tr>

<tr>

</td>

</tr>

</tbody>

</table>

</td>

Figure 16.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td rowspan="2" align="left" valign="top" >Step 17.

448

Attach the Little Grip to the Lexan as shown, using three

449

4-40 x .375" button head screws and acorn locking nuts. Only three

450

screws are used (shown in the image) as the body of the gripper servo

451

is in the way for the fourth.

452

Make sure the HS-422 (a HS-322HD

453

may be substituted) servo is aligned to mid-position, and the gripper

454

is halfway open. Now the servo and gripper will be aligned correctly.

455

Remove the servo screw and horn. Slide the servo into the gripper from

456

the bottom. You may need to wiggle it a bit to get it seated properly.

457

Use the servo screw to attach the servo. Tighten this down, but then

458

unscrew it half a turn. Too much friction can bind the servo.

<tbody>

<tr>

<td >3 x (NOT four)

</td>

<td >3 x (NOT four)

</td>

</tr>

<tr>

</tr>

</tbody>

</table>

Step 18.

Add 6" servo extender cables to the wrist and gripper servos.

</td>

Figure 17.

</td>

</tr>

<tr>

Figure 18.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 19.

490

Carefully bend the wrist servo back as far as it will go, and

491

use wire ties to secure the servo cables as shown. Make sure to leave

492

slack in the gripper servo cable, don't pull it too tight.</td>

Figure 19.</td>

</tr>

<tr>

</td>

</tr>

<tr>

Step 20.

Carefully stretch the arm forward as far as it will go, and

504

use wire ties to secure the servo cables as shown. Make sure to leave

505

slack in the cables, don't pull them too tight. Plug the servos in

506

according to Table 20.

<tbody>

<tr>

<td >

<tbody>

<tr>

<td bordercolor="#808080" align="center" bgcolor="#c0c0c0" width="25%">SSC-32

518

I/O</td>

519

<td bordercolor="#808080" align="center" bgcolor="#c0c0c0" width="75%">Servo</td>

</tr>

<tr>

</tr>

<tr>

<td bordercolor="#C0C0C0" align="center" bgcolor="#ffffff" width="75%">Shoulder</td>

</tr>

<tr>

<td bordercolor="#C0C0C0" align="center" bgcolor="#ffffff" width="75%">Elbow</td>

</tr>

<tr>

<td bordercolor="#C0C0C0" align="center" bgcolor="#ffffff" width="75%">Wrist</td>

</tr>

<tr>

<td bordercolor="#C0C0C0" align="center" bgcolor="#ffffff" width="75%">Gripper</td>

</tr>

<tr>

<td bordercolor="#C0C0C0" align="center" bgcolor="#ffffff" width="75%">Wrist

544

Rotate (Optional)</td>

</tr>

</tbody>

</table>

</div>

</td>

</tr>

<tr>

Table 20.

</td>

</tr>

</tbody>

</table>

</center>

</div>

</td>

Figure 20.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 21a (SSC-32 / Lynxterm). If

569

you have the SSC-32U (USB connector), please proceed with Step 21b. If

570

you have the SSC-32 (serial connector), we'll use LynxTerm to test the

571

servos and confirm that they're all plugged into the proper channels (just as in the Base Assembly Instructions).

572

If you have not done so before, download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm</a>. Connect the SSC-32 to

573

the serial port and apply power. The green LED should light up and stay

574

on

575

until it receives a valid serial command. Run the LynxTerm program. If

576

LynxTerm cannot connect, please consult the <a href="https://community.robotshop.com/forum/t/serial-usb-to-serial-port-troubleshooting/17938" target="_blank">serial

577

and USB-to-serial troubleshooting guide</a>.

578

579

580

Now test the servos and connections by selecting a channel, and moving

581

the servo carefully using the slider bar. Verify that the servos are

582

plugged into the channels as listed in Table 20. Easy does it; this is

583

real time control, so be careful! Select channels 0 through 4 one at a time and test that each works.

</td>

Figure 21a (Lynxterm).

</td>

</tr>

<tr>

</tr>

<tr>

<td style="vertical-align: top;">Step

601

21b (SSC-32U / Servo Utility).

602

Just like in the base instructions, we will use the SSC-32 Servo

603

Sequencer Utility to test the servos and confirm they are all plugged

604

into their proper servo channels and oriented correctly. If not done so

605

before, download and install the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/ssc-32-sequencer/" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB

606

cable and power the board using the on/off switch. Run

607

the program.

608

609

The SSC-32U is shipped with a baud rate of 9600. Ensure the baud rate

610

towards the bottom right of the window is set to 9600 (not 115200). The

611

software should automatically detect which COM port is connected to the

612

SSC-32U, and have installed the <a href="http://www.ftdichip.com/Drivers/VCP.htm" target="_blank">FTDI

613

(USB to serial) drivers</a> automatically.

614

Ensure Servos 0 4 are checked off in the software (and therefore

615

accessible). You can now move the sliders to see each servo rotate. Verify that the servos are

616

plugged into the channels as listed in Table 21. Easy does it; this is

617

real time control, so be careful.

618

619

For more information, please consult the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/ssc-32-sequencer/WebHome/SSC32%20Servo%20Sequencer.pdf" target="_blank">SSC32 Servo Sequencer Guide</a>.

</td>

Figure 21b (SSC-32 Utility).</td>

</tr>

<tr>

</td>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 22a (SSC-32 / Lynxterm).

635

Click on the "All = 1500" button in LynxTerm. This will command the

636

servos to hold center position. Your arm should look like Figure 22. If

637

any joint is off by more than 15°, then you may have made an error in

638

assembly.

639

640

If you did not purchase RIOS software, please proceed to step 27.

</td>

Figure 22.

</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td style="vertical-align: top;">Step 22b (SSC-32U / Servo Utility).

658

Click on the "Calibrate" button in the SSC-32 Servo Sequencer Utility.

659

A knob next to each servo will appear (figure 22b). This knob is used

660

to fine tune the servo's center position. The knob is not intended to

661

be rotated: click the knob you wish to rotate, keeping the mouse button

662

down, and drag up and down to rotate the knob. Do this for each servo

663

until the arm looks like figure 22, and angles are 90 and 180 degrees.

664

If

665

any joint is off by more than 15°, then you may have made an error in

666

assembly.

667

668

Once all servos have been properly positioned, click the icon

669

"Calibrate" once again, and the offset values will be stored on the

670

SSC-32 / SSC-32U.

671

672

If you did not purchase the RIOS software, please proceed to step 27.</td>

673

674

675

Figure 22b (SSC-32 Utility).</td>

</tr>

<tr>

</td>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 23 (RIOS Users Only).

685

To use the RIOS Arm control software, you need to make one

686

minor modification. Remove the servo horn screw from the elbow servo.

687

Pull the servo horn off the servo, lift the arm two 'clicks' (30°) at

688

the elbow and reattach the servo horn and screw. Note, the Hitec spline

689

has 24 grooves, so each groove is 15°.</td>

Figure 23.</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 24 (RIOS Users Only).

698

At this point the arms is assembled and tested using LynxTerm. If your

699

robot came with RIOS, we can now install RIOS and calibrate the arm to

700

the software. For those using a different program such as FlowBotics or

701

FlowStone, refer to the software's user guide. Use the RIOS Help File

702

to calibrate and use the arm.

703

Install RIOS, following the

704

on-screen installation prompts. The serial number is on the back of the

705

CD sleeve.

706

Use the RIOS Help File to

707

calibrate and use the arm, following Steps 1-7. When you get to Step 8

708

in the help file, please use the following instructions instead. Click

709

on the "Arm" button, then click on the "Arm" button in the "Arm size"

710

section, and then click on the AL5A arm image on the popup screen.

711

Please take the time to do an

712

accurate calibration. The performance of the arm will only be as good

713

as the calibration. If the on screen virtual arm does not match the

714

real arm this is a sign of an inaccurate calibration. After calibration

715

please study the RIOS manual carefully to learn how to store and

716

playback sequences for the arm.

</td>

Figure 24 (RIOS).

</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 25 (RIOS Users Only).

729

To calibrate the arm's shoulder servo, click the "SSC-32" button.</td>

Figure 25 (RIOS).

</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 26 (RIOS Users Only).

742

Select the Shoulder, servo #2. Move the shoulder slider up to move the

743

shoulder forward so that it looks like Figure 27-2. Set the Min Deg

744

angle -90°. Right click on the slider to set this as the Min Position.

745

Now the servo will not go past this value, and the program now knows

746

this value is exactly 90° from centered.

747

Now move the slider down to move

748

the shoulder backward so that it looks like Figure 27-3. Set the Max

749

Deg angle to 45°. Right click on the slider to set this as the Max

750

Position. Now the servo will not go past this value, and the program

751

now knows this value is exactly 45° from centered.

752

The next step is to read and

753

study the RIOS users guide. It is accessible by clicking on the help

754

icon on the main screen or by navigating to the install directory

755

(c:\Program Files\RIOS_SSC-32\) and opening the Help.pdf file. This

756

manual explains in great detail how to use the arm.

</td>

Figure 26-1 (RIOS).

</td>

</tr>

<tr>

</tr>

<tr>

Figure 26-2.

</td>

Figure 26-3.

</td>

</tr>

<tr>

</tr>

<tr>

<td align="left" valign="top" >Step 27.

783

To connect springs for load-balancing, replace the servo

784

attachment hardware in the locations shown, following the diagrams

785

below. Hook the springs together after they're secured.

</td>

Figure 27.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td align="left" valign="top" >Step 28.

798

The arm assembly is complete. The arm is robust mechanically,

799

but the servos can be damaged by improper use. An example would be if

800

the arm was told to move to an unobtainable position, like the surface

801

the arm is mounted to, or by crashing the arm into itself, or other

802

objects. The elbow servo is the most vulnerable because it holds the

803

entire weight of the forearm. Load balancing springs should be added to

804

reduce some of this load.

805

806

If you purchased FlowBotics Studio,

807

FlowStone or FlowArm, you can proceed with the instruction guide(s)

808

associated with those programs.

809

810

811

People do not like holding heavy objects with their arms outstretched in front of them. Servo based robot arms don't like it much either. Remember, the most important rule for servo based robot arms: Park the arm when not in motion! When it's moving or at rest it's usually ok. When it's holding an object it should do so for the minimum amount of time required to do the job. You can always touch the servo case to see if it's getting hot.

</td>

</td>

</tr>

</tbody>

</table>

Wiki source code of AL5A Arm Assembly Instructions Rev. 2.1

Navigation