Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -44,7 +44,7 @@
44	44	can be more difficult to remove. If you have trouble you can gently
45	45	scrape the cut edge, then use duct tape to lift the covering off.</font></p>
46	46	<p><font face="Verdana" size="2">For further information on
47		-lexan, see <a href="http://www.lynxmotion.com/images/html/infolexa.htm" target="_blank">this
	47	+lexan, see <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/support/polycarbonate-info-page/" target="_blank">this
48	48	page</a>.</font></p>
49	49	</td>
50	50	<td align="center" valign="top" ><font face="Verdana" size="2"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5b-arm-rev-2-1/WebHome/lexan01.jpg" border="2" height="240" hspace="10" width="320"><br>
...	...	@@ -585,10 +585,10 @@
585	585	SSC-32, as in the Base Assembly Instructions, we'll use LynxTerm to
586	586	test the
587	587	servos and confirm that they're all plugged into the proper channels.
588		-If not done before, download and install <a href="http://www.lynxmotion.com/showproduct.aspx?productID=567&amp;CategoryID=15#downloads" target="_blank">LynxTerm v1.08</a> or higher. Connect the SSC-32 to
	588	+If not done before, download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm</a>. Connect the SSC-32 to
589	589	the serial port and apply power. The green LED should light and stay on
590	590	until it receives a valid serial command. Run the LynxTerm program. If
591		-LynxTerm cannot connect, please consult the <a href="http://www.lynxmotion.net/viewtopic.php?t=4702" target="_blank">serial
	591	+LynxTerm cannot connect, please consult the <a href="https://community.robotshop.com/forum/t/serial-usb-to-serial-port-troubleshooting/17938" target="_blank">serial
592	592	and USB-to-serial troubleshooting guide</a>.</font>
593	593	<p><font face="Verdana" size="2"><b>Step 22.</b><br>
594	594	Now test the servos and connections by selecting a channel, and moving
...	...	@@ -610,7 +610,7 @@
610	610	</b>Just like in the base instructions, we will use the SSC-32 Servo
611	611	Sequencer Utility to test the servos and confirm they are all plugged
612	612	into their proper servo channels and oriented correctly. If not done so
613		-before, download and install the <a href="http://www.lynxmotion.com/p-895-free-download-ssc-32-servo-sequencer-utility-created-using-flowbotics-studio.aspx" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
	613	+before, download and install the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/ssc-32-sequencer/" target="_blank">SSC-32 Servo Sequencer Utility</a>. Connect the USB
614	614	cable and power the board using the on/off switch.</font><font face="Verdana" size="2"> Run
615	615	the program.<br>
616	616	<br>
...	...	@@ -624,7 +624,7 @@
624	624	plugged into the channels as listed in Table 20. Easy does it; this is
625	625	real time control, so be careful.<br>
626	626	<br>
627		-For more information, please consult the <a href="http://www.flowbotics.com/manuals/ssc-32_servo_sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a>. </font></td>
	627	+For more information, please consult the <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/ssc-32-sequencer/WebHome/SSC32%20Servo%20Sequencer.pdf" target="_blank">SSC-32 Servo Sequencer Utility manual</a>. </font></td>
628	628	<td style="vertical-align: top; text-align: center;"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-arms/al5b-arm-rev-2-1/WebHome/RB-Dsp-07.jpg" border="2" height="240" hspace="10" width="320"><br>
629	629
630	630	<font face="Verdana" size="2">Figure 21b (SSC-32 Utility).</font></td>