Changes for page LSS-ADA Board (USB Mini)
Last modified by Eric Nantel on 2024/07/03 09:39
Change comment: There is no comment for this version
Summary
-
Page properties (2 modified, 0 added, 0 removed)
Details
- Page properties
-
- Author
-
... ... @@ -1,1 +1,1 @@ 1 -xwiki:XWiki.B Daouas1 +xwiki:XWiki.CBenson - Content
-
... ... @@ -1,17 +1,18 @@ 1 1 [[image:LSS-ADA.png||alt="LSS-Adapter.png" width="350"]] 2 +**Table of Contents** 2 2 3 3 {{toc/}} 4 4 5 5 = Description = 6 6 7 -The Lynxmotion Smart Servo (LSS) Adapter Board is an electronic board which allows for easy con figuration and control of the Lynxmotion Smart Servos. The board includes a variety of features and functionality and provides power distribution via six LSSsixconnectors. The board is intended to be powered from a LiPo battery through the on-board male XT60 connector, or with a wall adapter with a female XT60 connector. There are many ways to interface with this board, as described below.8 +The Lynxmotion Smart Servo (LSS) Adapter Board is an electronic board which allows for easy connection to and control of the Lynxmotion Smart Servos. The board includes a variety of features and functionality and provides power distribution via six LSS connectors. The board is ideally intended to be powered from a LiPo battery through the on-board male XT60 connector, or with a wall adapter equipped with a female XT60 connector. There are many ways to interface with this board, as described below. 8 8 9 9 = Features = 10 10 11 -* Control LSS actuators via 6x connectors (4-pins Molex)12 -* On-board XBee Socket13 -* Can workas anXBee explorerUSBboard14 -* Arduino s tackable shield compatible12 +* Connect to and control LSS actuators via 6x connectors 13 +* On-board Bee Socket (XBee, Bluetooth Bee WiFi Bee modules) 14 +* Can function as a USB XBee explorer board 15 +* Arduino shield compatible using stacking headers 15 15 * Selectable control method : USB, Arduino or XBee 16 16 * Raspberry Pi B+/2/3 mounting compatibility 17 17 * XT60 Connector for power input ... ... @@ -19,19 +19,19 @@ 19 19 20 20 = Specifications = 21 21 22 -* 3A (max) continuous current per channel23 +* Continuous current per connector: 3A (max) 23 23 * Built-in USB to serial (FTDI Virtual COM Port chip) 24 24 * Built-in 5V regulator 25 25 * Built-in 3.3V regulator 26 26 * USB Mini connector 27 -* Dimensions 28 -* Mounting hole sdiameter28 +* Dimensions: 64 x 64 x 15mm 29 +* Mounting hole diameter: 3.1mm 29 29 30 30 ((( 31 31 = Communication / Control = 32 32 33 33 * Mini USB: ex: computer, laptop, Raspberry Pi 34 -* Arduino shield compatible 35 +* Arduino shield compatible (using M/M or extended M/F headers) 35 35 * TTL UART Microcontroller or FPGA control (5V) via Tx, Rx, GND pins 36 36 * Wireless module with XBee footprint (Bluetooth Bee, WiFi Bee etc.) 37 37 ))) ... ... @@ -42,10 +42,10 @@ 42 42 43 43 = Pinout = 44 44 45 -|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-ADAPTER-PinOut.png"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]| 46 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]| 47 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]| 48 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]| 46 +|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-ADAPTER-PinOut.png"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|**Servo Vcc pin**: Refer to the Voltage section of the LSS - Specifications page to understand which voltages are meant to be connected to this pin. 47 +|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground"). 48 +|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Rx pin**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin 49 +|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Tx pin**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output. 49 49 50 50 |(% colspan="2" style="width:350px" %)((( 51 51 = Wiring =