Wiki source code of LSS-P - Arduino Custom Firmware

Version 7.2 by Eric Nantel on 2023/10/18 14:25

3.1	1
	2
	3	Disclaimer
	4
	5
5.1	6	= Prerequisites =
3.1	7
	8
	9	= Setup =
	10
6.1	11	(% style="width:800px" %)
7.1	12	\|(% colspan="3" rowspan="1" style="width:10px" %)Hardware\|(% style="width:100px" %)Datasheet\|(% style="width:100px" %)Pins\|(% style="width:100px" %)Address\|(% style="width:100px" %)Examples
	13	\|(% style="width:10px" %) \|(% colspan="6" rowspan="1" %)RGB LED
	14	\| \|(% style="width:10px" %) \|Red\| \|PD12\| \|
	15	\| \| \|Green\| \|PD13\| \|
	16	\| \| \|Blue\| \|PD10\| \|
7.2	17	\| \|(% colspan="2" rowspan="1" %)Inertial Measuring Unit (IMU)\|(% colspan="4" rowspan="1" %)STMicroelectronics LSM6DSLTR
7.1	18	\| \| \|I2C / SDA\| \|PB7\| \|
	19	\| \| \|I2C / SCL\| \|PB6\| \|
	20	\| \|(% colspan="2" rowspan="1" %)Temperature PCB - ???\| \| \| \|
	21	\| \| \|I2C / SDA\| \| \| \|
	22	\| \| \|I2C / SCL\| \| \| \|
	23	\| \|(% colspan="2" rowspan="1" %)EERPROM\|(% colspan="4" rowspan="1" %)Onsemi CAT24C32HU4I-GT3
	24	\| \| \|I2C / SDA\| \| \| \|
	25	\| \| \|I2C / SCL\| \| \| \|
	26	\| \| \| \| \| \| \|
	27	\| \| \| \| \| \| \|
	28	\| \| \| \| \| \| \|
	29	\| \| \| \| \| \| \|
	30	\| \| \| \| \| \| \|
	31	\| \| \| \| \| \| \|
	32	\| \| \| \| \| \| \|
	33	\| \| \| \| \| \| \|
	34	\| \| \| \| \| \| \|
	35	\| \| \| \| \| \| \|
	36	\| \| \| \| \| \| \|
	37	\| \| \| \| \| \| \|
	38	\| \| \| \| \| \| \|
	39	\| \| \| \| \| \| \|
	40	\| \| \| \| \| \| \|
	41	\| \| \| \| \| \| \|
3.1	42
	43	= Pinout =
	44
	45
	46	= Examples =
	47
	48	(% style="width:800px" %)
	49	\|Hardware\|Example
	50	\|Push Button\|
	51	\|EEPROM\|
	52	\|IMU\|
	53	\|Stepper Driver / Stepper\|
	54	\| \|
	55	\| \|
	56	\| \|
	57
	58

Navigation