Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -124,8 +124,8 @@
124	124	| |[[**Default** Configuration>>||anchor="HDefault26confirm"]]|(% style="text-align:center" %)DEFAULT|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Revert to firmware default values. See command for details
125	125	| |[[Firmware **Update** Mode>>||anchor="HUpdate26confirm"]]|(% style="text-align:center" %)UPDATE|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Update firmware. See command for details.
126	126	| |[[**Confirm** Changes>>||anchor="HConfirm"]]|(% style="text-align:center" %)CONFIRM|(% style="text-align:center" %) |(% style="text-align:center" %) | | |
	127	+| |[[**ID** Number >>||anchor="HIdentificationNumber28ID29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QID|(% style="text-align:center" %)CID|0| |Reset required after change. ID 254 is a "broadcast" which all servos respond to.
127	127	| |[[**E**nable CAN **T**erminal>>||anchor="HConfigureRCMode28CRC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QET|(% style="text-align:center" %)CET| |0 or 1|0: Disable  1: Enable
128		-| |[[**ID** Number >>||anchor="HIdentificationNumber28ID29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QID|(% style="text-align:center" %)CID|0| |Reset required after change. ID 254 is a "broadcast" which all servos respond to.
129	129	| |[[**U**SB **C**onnection State>>||anchor="HBaudRate"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QUC|(% style="text-align:center" %) | |0 or 1|0: Not connected 1: Connected
130	130	| |**Q**uery **F**irmware **R**elease|(% style="text-align:center" %) |(% style="text-align:center" %)QFR|(% style="text-align:center" %) | | |
131	131
...	...	@@ -224,9 +224,28 @@
224	224	(% style="color:inherit; font-family:inherit" %)Ex: #5CONFIRM<cr>
225	225
226	226	(% style="color:inherit; font-family:inherit" %)This command is used to confirm changes after a Default or Update command.
227		-Note: After the CONFIRM command is sent, the servo will automatically perform a RESET.(%%)
228		-
	227	+Note: After the CONFIRM command is sent, the servo will automatically perform a RESET.
229	229
	229	+====== (% style="color:inherit; font-family:inherit" %)__Enable CAN Terminal Resistor (**ET**)__(%%) ======
	230	+
	231	+Query Enable CAN Terminal Resistor (**QET**)
	232	+
	233	+Ex: #5QET<cr> might return *QET0<cr>
	234	+
	235	+This means that servo with ID 5 is NOT configured as the last servo in the CAN bus.
	236	+
	237	+Configure Enable CAN Terminal Resistor (**CET**)
	238	+
	239	+(% style="color:inherit; font-family:inherit" %)Ex: #5CET1<cr>
	240	+
	241	+(% style="color:inherit; font-family:inherit" %)This commands sets servo with ID 5 as being the last in the CAN Bus. The last servo in a CAN bus must be configured this way.
	242	+
	243	+====== __USB Connection Status (**UC**)__ ======
	244	+
	245	+Query USB Connection Status (**QUC**)
	246	+
	247	+Ex: #5QUC<cr> might return *5QUC1<cr> meaning the servo is connected via USB
	248	+
230	230	== Motion ==
231	231
232	232	====== __Position in Degrees (**D**)__ ======