LSS-P - Communication Protocol

(% class="wikigeneratedid" id="HTableofContents" %)

6

**Page Contents**

= Serial Protocol =

The Lynxmotion Smart Servo (LSS) PRO serial protocol was created in order to be as simple and straightforward as possible from a user perspective ("human readable format"), while at the same time staying compact and robust yet highly versatile. The protocol was based on Lynxmotion's Smart Servo (LSS) protocol, which itself was based on the SSC-32 & SSC-32U RC servo controllers. The LSS PRO series and normal LSS share many of the same commands, but because of higher angular precision, slightly different operation and different features, the two protocols do not fully overlap.

13

14

In order to be able to control each servo individually with commands, the first step should be to assign a different ID number to each servo (see details on the Configure ID, or "CID" command [[here>>doc:||anchor="HIdentificationNumber28ID29"]]). Only the servo(s) which have been configured to a specific ID will act on a command sent to that ID. There is currently no CRC or checksum implemented as part of the protocol.

= Action Commands =

Action commands tell the servo, within that session, to do something (i.e. "take an action"). The types of action commands which can be sent are described below, and they cannot be combined with other commands such as queries or configurations. Only one action command can be sent at a time. Action commands are session-specific, therefore once a servo is power cycled, it will not have any "memory" of previous actions or [[virtual positions>>||anchor="HVirtualAngularPosition"]] (described below). Action commands are sent serially to the servo and must be sent in the following format:

19

20

1. Start with a number sign **#** (Unicode Character: U+0023)

21

1. Servo ID number as an integer (assigning an ID described below)

22

1. Action command (one or more letters, no whitespace, capital or lowercase from the list below)

23

1. Action value in the correct units with no decimal

24

1. End with a carriage return **\r** or **<cr>** Unicode Character (U+000D)

(((

Ex: #5D130000<cr>

This sends a serial command to all servo's RX pins which are connected to the bus and only servo(s) with ID #5 will move to a position (13000 in hundredths of degrees) of 130.00 degrees. Any servo on the bus which does not have ID 5 will take no action when receiving this command.

== Modifiers ==

Modifiers can only be used with certain **action commands**. The format to include a modifier is:

34

35

1. Start with a number sign **#** (Unicode Character: U+0023)

36

1. Servo ID number as an integer

37

1. Action command (one to three letters, no spaces, capital or lowercase from a subset of action commands below)

38

1. Action value in the correct units with no decimal

39

1. Modifier command (one or two letters from the list of modifiers below)

40

1. Modifier value in the correct units with no decimal

41

1. End with a carriage return **\r** or **<cr>** Unicode Character (U+000D)

42

43

Ex: #5D13000T1500<cr>This results in the servo with ID #5 rotating to a position (1800 in tenths of degrees) of 130.00 degrees in a time ("T") of 1500 milliseconds (1.5 seconds).

== Queries ==

Query commands request information from the servo. Query commands are also similar to action and configuration commands and must use the following format:

48

49

1. Start with a number sign **#** (Unicode Character: U+0023)

50

1. Servo ID number as an integer

51

1. Query command (one to four letters, no spaces, capital or lower case)

52

1. End with a carriage return **\r** or **<cr>** Unicode Character (U+000D)

53

54

Ex: #5QD<cr> Query the position in (hundredths of) degrees for servo with ID #5The query will return a serial string (almost instantaneously) via the servo's Tx in the following format:

55

56

1. Start with an asterisk * (Unicode Character: U+0023)

57

1. Servo ID number as an integer

58

1. Query command (one to four letters, no spaces, capital letters)

59

1. The reported value in the units described, no decimals.

60

1. End with a carriage return **\r** or **<cr>** Unicode Character (U+000D)

61

62

There is currently no option to control how fast a servo replies after it has received a query command, therefore when sending a query command to the bus, the controller should be prepared to immediately "listen" for and parse the reply. Sending multiple queries to multiple servos on a bus in fast succession may result in replies overlapping and giving incorrect or corrupt data. As such, the controller should receive a reply before sending a new query command. A reply to the query sent above might be:

Ex: *5QD13000<cr>

This indicates that servo #5 is currently at 130.00 degrees (13000 tenths of degrees).

== Configurations ==

Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session. Not all action commands have a corresponding configuration command and vice versa. Configuration commands are not cumulative; this means that if two of the same configuration commands are sent, one after the next, only the last configuration is used and stored.

71

72

The format to send a configuration command is identical to that of an action command:

73

74

1. Start with a number sign **#** (Unicode Character: U+0023)

75

1. Servo ID number as an integer

76

1. Configuration command (two to four letters, no spaces, capital or lower case)

77

1. Configuration value in the correct units with no decimal

78

1. End with a carriage return **\r** or **<cr>** Unicode Character (U+000D)

Ex: #5CO-500<cr>

This configures an absolute origin offset ("CO") with respect to factory origin of servo with ID #5 and changes the offset for that session to -5.00 degrees (500 hundredths of degrees). Once the servo is powered off and on, zeroing the servo will cause it to move to -5.00 degrees with respect to the factory origin and report its position as 0 degrees. Configuration commands can be undone / reset either by sending the servo's default value for that configuration, or by doing a factory reset that clears all configurations (through the button menu or with DEFAULT command described below).

83

84

**Session vs Configuration Query**

85

86

By default, the query command returns the session's value. Should no action commands have been sent to change the session value, it will return the value saved in EEPROM which will either be the servo's default, or modified with a configuration command. In order to query the value stored in EEPROM (configuration), add a '1' to the query command:

87

88

Ex: #5CSR10<cr> immediately sets the maximum speed for servo #5 to 10rpm (explained below) and changes the value in memory.

89

90

After RESET, a command of #5SR4<cr> sets the session's speed to 4rpm, but does not change the configuration value in memory. Therefore:

91

92

#5QSR<cr> or #5QSR0<cr> would return *5QSR4<cr> which represents the value for that session, whereas

93

94

#5QSR1<cr> would return *5QSR10<cr> which represents the value in EEPROM

95

96

The ability to store a "virtual angular position" is a feature which allows for rotation beyond 360 degrees, permitting multiple rotations of the output horn, moving the center position and more. The "absolute position" would be the angle of the output shaft with respect to a 360.00 degree circle and can be obtained by taking the modulus (with respect to 360 degrees) of the value. For example if the virtual position is reported as 153350 (or 1533.50 degrees), taking the modulus would give 93.5 degrees (36000 * 4 + 9350 = 153350) as the absolute position (assuming no origin offset).

97

98

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-positions.jpg||alt="LSS-servo-positions.jpg"]]

99

100

In this example, the gyre direction (explained below, a.k.a. "rotation direction") is positive (clockwise), and origin offset has not been modified. Each square represents 30 degrees. The following command is sent:

101

102

#1D-3000<cr> This causes the servo to move to -30.00 degrees (green arrow)

103

104

#1D21000<cr> This second position command is sent to the servo, which moves it to 210.00 degrees (orange arrow)

105

106

#1D-42000<cr> This next command rotates the servo counterclockwise to a position of -420.00 degrees (red arrow), which means one full rotation of 360 degrees plus 60.00 degrees (420.00 - 360.00), with a virtual position of -420.0 degrees.

107

108

Although the final physical position would be the same as if the servo were commanded to move to -60.00 degrees, the servo is in fact at -420.00 degrees.

109

110

#1D48000<cr> This new command is sent which would then cause the servo to rotate from -420.00 degrees to 480.00 degrees (blue arrow), which would be a total of 900 degrees of clockwise rotation, or 2.5 complete rotations.

111

112

#1D33000<cr> would cause the servo to rotate from 480.0 degrees to 330.00 degrees (yellow arrow).

113

114

If the servo loses power or is power cycled, it also loses the virtual position associated with that session. For example, if the virtual position was 480.00 degrees before power is cycled, upon power up the servo's position will be read as +120.00 degrees from zero (assuming center position has not been modified). The virtual position range at power-up is [-180.00°, 180.00°].

)))

= Command List =

**Latest firmware version currently : v0.0.780**

120

121

|(% colspan="8" style="color:orange; font-size:18px" %)[[**Communication Setup**>>||anchor="HCommunicationSetup"]]

122

123

| |[[**Reset**>>||anchor="HReset"]]|(% style="text-align:center" %)RESET|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Soft reset. See command for details.

124

| |[[**Default** Configuration>>||anchor="HDefault26confirm"]]|(% style="text-align:center" %)DEFAULT|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Revert to firmware default values. See command for details

125

| |[[Firmware **Update** Mode>>||anchor="HUpdate26confirm"]]|(% style="text-align:center" %)UPDATE|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Update firmware. See command for details.

126

| |[[**Confirm** Changes>>||anchor="HConfirm"]]|(% style="text-align:center" %)CONFIRM|(% style="text-align:center" %) |(% style="text-align:center" %) | | |

127

| |[[**ID** Number >>||anchor="HIDNumber28ID29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QID|(% style="text-align:center" %)CID|0| |Reset required after change. ID 254 is a "broadcast" which all servos respond to.

128

| |[[**E**nable CAN **T**erminal>>doc:||anchor="HEnableCANTerminalResistor28ET29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QET|(% style="text-align:center" %)CET| |0 or 1|0: Disable 1: Enable

129

| |[[**U**SB **C**onnection Status>>||anchor="HUSBConnectionStatus28UC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QUC|(% style="text-align:center" %) | |0 or 1|0: Not connected 1: Connected

130

| |[[**Q**uery **F**irmware **R**elease>>doc:||anchor="HFirmwareRelease28FR29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QFR|(% style="text-align:center" %) | | |

131

132

|(% colspan="8" style="color:orange; font-size:18px" %)[[**Motion**>>||anchor="HMotion"]]

133

134

| |[[Position in **D**egrees>>||anchor="HPositioninDegrees28D29"]]|(% style="text-align:center" %)D|(% style="text-align:center" %)QD/QDT|(% style="text-align:center" %) | |1/100°|

135

| |[[**M**ove in **D**egrees (relative)>>||anchor="H28Relative29MoveinDegrees28MD29"]]|(% style="text-align:center" %)MD|(% style="text-align:center" %) |(% style="text-align:center" %) | |1/100°|

136

| |[[**W**heel mode in **D**egrees>>||anchor="HWheelModeinDegrees28WD29"]]|(% style="text-align:center" %)WD|(% style="text-align:center" %)QWD/QVT|(% style="text-align:center" %) | |°/s|A.K.A. "Speed mode" or "Continuous rotation"

137

| |[[**W**heel mode in **R**PM>>||anchor="HWheelModeinRPM28WR29"]]|(% style="text-align:center" %)WR|(% style="text-align:center" %)QWR|(% style="text-align:center" %) | |RPM|A.K.A. "Speed mode" or "Continuous rotation"

138

| |[[**Q**uery Motion Status>>||anchor="HQueryStatus28Q29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)Q|(% style="text-align:center" %) | |1 to 8 integer|See command description for details

139

| |[[**L**imp>>||anchor="HLimp28L29"]]|(% style="text-align:center" %)L|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Removes power from stepper coils

140

| |[[**H**alt & Hold>>||anchor="HHalt26Hold28H29"]]|(% style="text-align:center" %)H|(% style="text-align:center" %) |(% style="text-align:center" %) | | |Stops (halts) motion profile and holds last position

141

142

|(% colspan="8" style="color:orange; font-size:18px" %)[[**Motion Setup**>>||anchor="HMotionSetup"]]

143

144

| |[[**O**rigin Offset>>||anchor="HOriginOffset28O29"]]|(% style="text-align:center" %)O|(% style="text-align:center" %)QO|(% style="text-align:center" %)CO|0|1/10°|

145

| |[[**A**ngular **R**ange>>||anchor="HAngularRange28AR29"]]|(% style="text-align:center" %)AR|(% style="text-align:center" %)QAR|(% style="text-align:center" %)CAR|1800|1/10°|

146

| |[[**A**ngular **A**cceleration>>||anchor="HAngularAcceleration28AA29"]]|(% style="text-align:center" %)AA|(% style="text-align:center" %)QAA|(% style="text-align:center" %)CAA|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).

147

| |[[**A**ngular **D**eceleration>>||anchor="HAngularDeceleration28AD29"]]|(% style="text-align:center" %)AD|(% style="text-align:center" %)QAD|(% style="text-align:center" %)CAD|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).

148

| |[[**G**yre Direction>>||anchor="HGyreDirection28G29"]]|(% style="text-align:center" %)G|(% style="text-align:center" %)QG|(% style="text-align:center" %)CG|1| |Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)

149

| |[[**F**irst Position (**D**eg)>>||anchor="HFirstPosition"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QFD|(% style="text-align:center" %)CFD|No value|1/10°|Reset required after change.

150

| |[[Maximum **S**peed in **D**egrees>>||anchor="HMaximumSpeedinDegrees28SD29"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %)QSD|(% style="text-align:center" %)CSD|Max|0.1°/s|SD overwrites SR / CSD overwrites CSR and vice-versa

151

| |[[Maximum **S**peed in **R**PM>>||anchor="HMaximumSpeedinRPM28SR29"]]|(% style="text-align:center" %)SR|(% style="text-align:center" %)QSR|(% style="text-align:center" %)CSR|Max|RPM|SD overwrites SR / CSD overwrites CSR and vice-versa

152

| |[[Step Mode>>doc:||anchor="HStepMode28SM29"]]|(% style="text-align:center" %)SM|(% style="text-align:center" %)QM|(% style="text-align:center" %)CSM|2|1, 2, 4|Numbers represent fractions: full step, ½ step, ¼ step

153

154

|(% colspan="8" style="color:orange; font-size:18px" %)[[**Modifiers**>>||anchor="HModifiers"]]

155

156

| |[[**S**peed in **D**egrees>>||anchor="HSpeed28S2CSD29modifier"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %) |(% style="text-align:center" %) | |1°/s|For D and MD action commands

157

| |[[**T**imed move>>||anchor="HTimedmove28T29modifier"]]|(% style="text-align:center" %)T|(% style="text-align:center" %) |(% style="text-align:center" %) | |ms|Time associated with D, MD commands

158

159

|(% colspan="8" style="color:orange; font-size:18px" %)[[**Telemetry**>>||anchor="HTelemetry"]]

160

161

| |[[**Q**uery PCB **T**emperature>>||anchor="HQueryTemperature28QT29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QT|(% style="text-align:center" %) | |°C|

162

| |[[**Q**uery **C**urrent>>||anchor="HQueryCurrent28QC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QC|(% style="text-align:center" %) | |mA|Nominal RMS value to stepper motor driver IC.

163

| |[[**Q**uery **M**odel **S**tring>>||anchor="HQueryModelString28QMS29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QMS|(% style="text-align:center" %) | | |Returns the model of servo (ex: LSS-ST1, LSS-HS1, LSS-HT1)

164

| |[[**Q**uery **F**irmware Version>>||anchor="HQueryFirmware28QF29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QF|(% style="text-align:center" %) | | |

165

| |[[**Q**uery Serial **N**umber>>||anchor="HQuerySerialNumber28QN29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QN|(% style="text-align:center" %) | | |Returns the unique serial number for the servo

166

| |[[**Q**uery **T**emperature **P**robe>>doc:||anchor="HQueryTemperatureProbe28QTP29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QTP|(% style="text-align:center" %) | | |Queries temperature probe fixed to the stepper motor

167

| |[[**Q**uery **T**emp of **M**CU>>doc:||anchor="HQueryMCUTemperature28QTM29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QTM|(% style="text-align:center" %) | | |

168

| |[[**Q**uery **T**emp of **C**ontroller>>doc:||anchor="HQueryTempofController28QTCW29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QTCW, QTCE|(% style="text-align:center" %) | | |(((

169

QTCW: Queries the temperature status of the motor controller (pre-warning)

170

171

QTCE: Queries the temperature status of the motor controller (over-temp error)

172

)))

173

| |[[**Q**uery **I**MU Linear **X**>>doc:||anchor="HQueryIMULinear28QIXQIYQIZ29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIX|(% style="text-align:center" %) | |mm/s^2|

174

| |[[**Q**uery **I**MU Linear **Y**>>doc:||anchor="HQueryIMULinear28QIXQIYQIZ29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIY|(% style="text-align:center" %) | |mm/s^2|

175

| |[[**Q**uery **I**MU Linear **Z**>>doc:||anchor="HQueryIMULinear28QIXQIYQIZ29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIZ|(% style="text-align:center" %) | |mm/s^2|

176

| |[[**Q**uery **I**MU Angular Accel **α** >>doc:||anchor="HQueryIMUAngular28QIAQIBQIC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIA|(% style="text-align:center" %) | |°/s^2|Query IMU Angular Accel α (Alpha)

177

| |[[**Q**uery **I**MU Angular Accel **β**>>doc:||anchor="HQueryIMUAngular28QIAQIBQIC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIB|(% style="text-align:center" %) | |°/s^2|Query IMU Angular Accel β (Beta)

178

| |[[**Q**uery **I**MU Angular Accel **γ**>>doc:||anchor="HQueryIMUAngular28QIAQIBQIC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QIC / QIG|(% style="text-align:center" %) | |°/s^2|Query IMU Angular Accel γ (Gamma)

179

180

|(% colspan="8" style="color:orange; font-size:18px" %)[[**RGB LED**>>||anchor="HRGBLED"]]

181

182

| |[[**LED** Color>>||anchor="HLEDColor28LED29"]]|(% style="text-align:center" %)LED|(% style="text-align:center" %)QLED|(% style="text-align:center" %)CLED| |0 to 7 integer|0=Off; 1=Red; 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White

183

184

= (% style="color:inherit; font-family:inherit" %)Details(%%) =

185

186

== (% style="color:inherit; font-family:inherit" %)Communication Setup(%%) ==

187

188

|(% colspan="2" %)(((

189

====== __Reset__ ======

)))

| |(((

Ex: #5RESET<cr>

This command does a "soft reset" and reverts all commands to those stored in EEPROM (i.e. configuration commands). Note: after a RESET command is received, the LSS will restart and perform initilization again, making it unavailable on the bus for a bit. See Session, note #2 for more details.

195

)))

196

197

|(% colspan="2" %)(((

198

====== (% style="color:inherit; font-family:inherit" %)__Default & confirm__(%%) ======

199

)))

200

|(% style="width:30px" %) |(((

201

(% style="color:inherit; font-family:inherit" %)Ex: #5DEFAULT<cr>

202

203

(% style="color:inherit; font-family:inherit" %)This command sets in motion the reset of all values to the default values included with the version of the firmware installed on that servo. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the DEFAULT function.

204

205

(% style="color:inherit; font-family:inherit" %)EX: #5DEFAULT<cr> followed by #5CONFIRM<cr>

206

207

(% style="color:inherit; font-family:inherit" %)Since it it not common to have to restore all configurations, a confirmation command is needed after a firmware command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will exit the command.

208

209

(% style="color:inherit; font-family:inherit" %)Note: After the CONFIRM command is sent, the servo will automatically perform a RESET.

210

)))

211

212

|(% colspan="2" %)(((

213

====== (% style="color:inherit; font-family:inherit" %)__Update & confirm__(%%) ======

214

)))

215

|(% style="width:30px" %) |(((

216

(% style="color:inherit; font-family:inherit" %)Ex: #5UPDATE<cr>

217

218

(% style="color:inherit; font-family:inherit" %)This command sets in motion the equivalent of a long button press when the servo is not powered in order to enter firmware update mode. This is useful should the button be broken or inaccessible. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the UPDATE function.

219

220

(% style="color:inherit; font-family:inherit" %)EX: #5UPDATE<cr> followed by #5CONFIRM<cr>

221

222

(% style="color:inherit; font-family:inherit" %)Since it it not common to have to update firmware, a confirmation command is needed after an UPDATE command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.

223

224

(% style="color:inherit; font-family:inherit" %)Note: After the CONFIRM command is sent, the servo will automatically perform a RESET.

225

)))

226

227

|(% colspan="2" %)(((

228

====== (% style="color:inherit; font-family:inherit" %)__Confirm__(%%) ======

229

)))

230

|(% style="width:30px" %) |(((

231

(% style="color:inherit; font-family:inherit" %)Ex: #5CONFIRM<cr>

232

233

(% style="color:inherit; font-family:inherit" %)This command is used to confirm changes after a Default or Update command.

234

Note: After the CONFIRM command is sent, the servo will automatically perform a RESET.

235

)))

236

237

|(% colspan="2" %)(((

238

====== (% style="color:inherit; font-family:inherit" %)__ID Number__(%%) ======

239

)))

240

|(% style="width:30px" %) |(((

241

This assigns ID #5 to the servo previously assigned to ID 0

242

243

(% style="color:inherit; font-family:inherit" %)Configure ID Number (**CID**)

244

245

(% style="color:inherit; font-family:inherit" %)Ex: #0CID5<cr>

246

247

The default ID is 0, so this sets the servo to ID 5.

248

249

Query ID Number (**QID**)

250

251

Ex: #254QID<cr> might return *254QID5<cr>

252

253

In this case, the broadcast ID is used to ensure the servo connected will reply with the ID. This can be used in case the ID assigned to a servo is forgotten.

254

)))

255

256

|(% colspan="2" %)(((

257

====== (% style="color:inherit; font-family:inherit" %)__Enable CAN Terminal Resistor__(%%) ======

258

)))

259

|(% style="width:30px" %) |(((

260

Query Enable CAN Terminal Resistor (**QET**)

261

262

Ex: #5QET<cr> might return *QET0<cr>

263

264

This means that servo with ID 5 is NOT configured as the last servo in the CAN bus.

265

266

Configure Enable CAN Terminal Resistor (**CET**)

267

268

(% style="color:inherit; font-family:inherit" %)Ex: #5CET1<cr>

269

270

(% style="color:inherit; font-family:inherit" %)This commands sets servo with ID 5 as being the last in the CAN Bus. The last servo in a CAN bus must be configured this way.

271

)))

272

273

|(% colspan="2" %)(((

274

====== __USB Connection Status__ ======

275

)))

276

|(% style="width:30px" %) |(((

277

Query USB Connection Status (**QUC**)

278

279

Ex: #5QUC<cr> might return *5QUC1<cr> meaning the servo is connected via USB

280

)))

281

282

|(% colspan="2" %)(((

283

====== __Firmware Release__ ======

284

)))

285

|(% style="width:30px" %) |(((

286

Query Firmware Release (**QFR**)

287

288

Ex: #5QFR<cr> might return *QFR11<cr> meaning it has a (random) firmware release version number 11.

289

290

This is used to verify if the firmware on the servos is up to date, or which version is running on the microcontroller.

)))

== Motion ==

====== __Position in Degrees (**D**)__ ======

Example: #5D1456<cr>

This moves the servo to an angle of 145.6 degrees, where the center (0) position is centered. Negative values (ex. -176 representing -17.6 degrees) could also be used. A full circle would be from -1800 to 1800 degrees. A value of 2700 would be the same angle (absolute position) as -900, except the servo would move in a different direction.

300

301

Larger values are permitted and allow for multi-turn functionality using the concept of virtual position (explained above).

302

303

Query Position in Degrees (**QD**)

304

305

Example: #5QD<cr> might return *5QD132<cr>

306

307

This means the servo is located at 13.2 degrees.

308

309

Query Target Position in Degrees (**QDT**)

310

311

Ex: #5QDT<cr> might return *5QDT6783<cr>

312

313

The query target position command returns the target virtual position during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond with the last target position used.

314

315

====== __(Relative) Move in Degrees (**MD**)__ ======

Example: #5MD123<cr>

The relative move command causes the servo to read its current position and move the specified number of tenths of degrees in the corresponding position. For example if the servo is set to rotate CW (default) and an MD command of 123 is sent to the servo, it will cause the servo to rotate clockwise by 12.3 degrees. Negative commands would cause the servo to rotate in the opposite configured direction.

321

322

====== __Wheel Mode in Degrees (**WD**)__ ======

Ex: #5WD90<cr>

This command sets the servo to wheel mode where it will rotate in the desired direction at the selected speed. The example above would have the servo rotate at 90.0 degrees per second clockwise (assuming factory default configurations).

327

328

Query Wheel Mode in Degrees (**QWD**)

329

330

Ex: #5QWD<cr> might return *5QWD90<cr>

331

332

The servo replies with the angular speed in degrees per second. A negative sign would indicate the opposite direction (for factory default a negative value would be counter clockwise).

333

334

====== __Wheel Mode in RPM (**WR**)__ ======

Ex: #5WR40<cr>

This command sets the servo to wheel mode where it will rotate in the desired direction at the selected rpm. Wheel mode (a.k.a. "continuous rotation") has the servo operate like a geared DC motor. The servo's maximum rpm cannot be set higher than its physical limit at a given voltage. The example above would have the servo rotate at 40 rpm clockwise (assuming factory default configurations).

339

340

Query Wheel Mode in RPM (**QWR**)

341

342

Ex: #5QWR<cr> might return *5QWR40<cr>

343

344

The servo replies with the angular speed in rpm. A negative sign would indicate the opposite direction (for factory default a negative value would be counter clockwise).

345

346

====== __(Relative) Move in Degrees (**MD**)__ ======

347

348

(% class="wikigeneratedid" id="HExample:235M15003Ccr3E" %)

349

Example: #5M1500<cr>

350

351

(% class="wikigeneratedid" id="HTherelativemoveinPWMcommandcausestheservotoreaditscurrentpositionandmovebythespecifiednumberofPWMsignal.ForexampleiftheservoissettorotateCW28default29andanMcommandof1500issenttotheservo2Citwillcausetheservotorotateclockwiseby90degrees.NegativePWMvaluewouldcausetheservotorotateintheoppositeconfigureddirection." %)

352

The relative move in PWM command causes the servo to read its current position and move by the specified number of PWM signal. For example if the servo is set to rotate CW (default) and an M command of 1500 is sent to the servo, it will cause the servo to rotate clockwise by 90 degrees. Negative PWM value would cause the servo to rotate in the opposite configured direction.

353

354

====== __Query Status (**Q**)__ ======

355

356

The status query describes what the servo is currently doing. The query returns an integer which must be looked up in the table below.

357

358

Ex: #5Q<cr> might return *5Q6<cr>, which indicates the motor is holding a position.

359

360

|(% style="width:25px" %) |***Value returned (Q)**|**Status**|**Detailed description**

361

| |ex: *5Q0<cr>|0: Unknown|LSS is unsure / unknown state

362

| |ex: *5Q1<cr>|1: Limp|Motor driving circuit is not powered and horn can be moved freely

363

| |ex: *5Q2<cr>|2: Free moving|Servo is rotating in duty motion / free move using the RDM command

364

| |ex: *5Q3<cr>|3: Accelerating|Increasing speed from rest (or previous speed) towards travel speed

365

| |ex: *5Q4<cr>|4: Traveling|Moving at a stable speed

366

| |ex: *5Q5<cr>|5: Decelerating|Decreasing from travel speed towards final position.

367

| |ex: *5Q6<cr>|6: Holding|Keeping current position (in EM0 mode, return will nornally be holding)

368

| |ex: *5Q7<cr>|7: Outside limits|{More details coming soon}

369

| |ex: *5Q8<cr>|8: Stuck|Motor cannot perform request movement at current speed setting

370

| |ex: *5Q9<cr>|9: Blocked|Similar to stuck, but the motor is at maximum duty and still cannot move (i.e.: stalled)

371

| |ex: *5Q10<cr>|10: Safe Mode|(((

372

A safety limit has been exceeded (temperature, peak current or extended high current draw).

373

374

Send a Q1 command to know which limit has been reached (described below).

375

)))

376

377

If a safety limit has been reached and exceeded, the LED will flash red and the servo will stop providing torque (no longer react to commands which cause the motor to rotate). In order to determine which limit has been reached, send a Q1 command. The servo must be RESET in order to return to normal operation, though if a limit is still detected (for example the servo is still too hot), it will revert back to Safe Mode.

378

379

|(% style="width:25px" %) |***Value returned (Q1)**|**Status**|**Detailed description**

380

| |ex: *5Q0<cr>|No limits have been passed|Nothing is wrong

381

| |ex: *5Q1<cr>|Current limit has been passed|Something cause the current to either spike, or remain too high for too long

382

| |ex: *5Q2<cr>|Input voltage detected is below or above acceptable range|Check the voltage of your batteries or power source

383

| |ex: *5Q3<cr>|Temperature limit has been reached|The servo is too hot to continue operating safely.

384

385

====== __Limp (**L**)__ ======

Example: #5L<cr>

This action causes the servo to go "limp". The microcontroller will still be powered, but the motor will not. As an emergency safety feature, should the robot not be doing what it is supposed to or risks damage, use the broadcast ID to set all servos limp #254L<cr>.

390

391

====== __Halt & Hold (**H**)__ ======

Example: #5H<cr>

This command causes the servo to stop immediately and hold that angular position. It overrides whatever the servo might be doing at the time the command is received (accelerating, travelling, deccelerating, etc.)

== Motion Setup ==

====== __Origin Offset (**O**)__ ======

400

401

Example: #5O2400<cr>This command allows you to change the origin of the servo in relation to the factory zero position for that session. As with all action commands, the setting will be lost upon servo reset / power cycle. Origin offset commands are not cumulative and always relate to factory zero. In the first image, the origin at factory offset '0' (centered).

402

403

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-default.jpg||alt="LSS-servo-default.jpg"]]

404

405

406

In the second image, the origin, and the corresponding angular range (explained below) have been shifted by +240.0 degrees:

407

408

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-origin.jpg||alt="LSS-servo-origin.jpg"]]

409

410

411

Origin Offset Query (**QO**)

412

413

Example: #5QO<cr> might return *5QO-13

414

415

This allows you to query the angle (in tenths of degrees) of the origin in relation to the factory zero position. In this example, the new origin is at -1.3 degrees from the factory zero.

416

417

Configure Origin Offset (**CO**)

Example: #5CO-24<cr>

This command allows you to change the origin of the servo in relation to the factory zero position in EEPROM. The setting will be saved upon servo reset / power cycle. Origin offset configuration commands are not cumulative and always relate to factory zero. The new origin is also used in RC mode. In the example, the new origin will be at -2.4 degrees from the factory zero.

422

423

====== __Angular Range (**AR**)__ ======

424

425

Example: #5AR1800<cr>

426

427

This command allows you to temporarily change the total angular range of the servo in tenths of degrees. This applies to the Position in Pulse (P) command and RC mode. The default for (P) and RC mode is 1800 (180.0 degrees total, or ±90.0 degrees). The image below shows a standard -180.0 to +180.0 range, with no offset:

428

429

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-default.jpg||alt="LSS-servo-default.jpg"]]

430

431

Below, the angular range is restricted to 180.0 degrees, or -90.0 to +90.0. The center has remained unchanged.

432

433

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-ar.jpg||alt="LSS-servo-ar.jpg"]]

434

435

436

Finally, the angular range action command (ex. #5AR1800<cr>) and origin offset action command (ex. #5O-1200<cr>) are used to move both the center and limit the angular range:

437

438

[[image:https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-communication-protocol/WebHome/LSS-servo-ar-o-1.jpg||alt="LSS-servo-ar-o-1.jpg"]]

439

440

441

Query Angular Range (**QAR**)

442

443

Example: #5QAR<cr> might return *5AR1800, indicating the total angular range is 180.0 degrees.

444

445

Configure Angular Range (**CAR**)

446

447

This command allows you to change the total angular range of the servo in tenths of degrees in EEPROM. The setting will be saved upon servo reset / power cycle.

448

449

====== __Angular Acceleration (**AA**)__ ======

450

451

The default value for angular acceleration is 100. Accepts values of between 1 and 100. Increments of 10 degrees per second squared.

Ex: #5AA30<cr>

This sets the angular acceleration for servo #5 to 30 degrees per second squared (°/s^^2^^).

456

457

Query Angular Acceleration (**QAA**)

458

459

Ex: #5QAA<cr> might return *5QAA30<cr>

460

461

This returns the servo's angular acceleration in degrees per second squared (°/s^^2^^).

462

463

Configure Angular Acceleration (**CAA**)

Ex: #5CAA30<cr>

This writes the angular acceleration of servo #5 to 30 degrees per second squared (°/s^^2^^) to EEPROM.

468

469

====== __Angular Deceleration (**AD**)__ ======

470

471

The default value for angular deceleration is 100. Accepts values of between 1 and 100. Increments of 10 degrees per second squared.

Ex: #5AD30<cr>

This sets the angular deceleration for servo #5 to 30 degrees per second squared (°/s^^2^^).

476

477

Query Angular Deceleration (**QAD**)

478

479

Ex: #5QAD<cr> might return *5QAD30<cr>

480

481

This returns the servo's angular deceleration in degrees per second squared (°/s^^2^^).

482

483

Configure Angular Deceleration (**CAD**)

Ex: #5CAD30<cr>

This writes the angular deceleration of servo #5 to 30 degrees per second squared (°/s^^2^^) to EEPROM.

488

489

====== __Gyre Direction (**G**)__ ======

490

491

"Gyre" is defined as a circular course or motion. The effect of changing the gyre direction is as if you were to use a mirror image of a circle. By default: CW = 1; CCW = -1.

Ex: #5G-1<cr>

This command will cause servo #5's positions to be inverted, effectively causing the servo to rotate in the opposite direction given the same command. For example in a 2WD robot, servos are often physically installed back to back, therefore setting one of the servos to a negative gyration, the same wheel command (ex WR30) to both servos will cause the robot to move forward or backward rather than rotate.

496

497

Query Gyre Direction (**QG**)

498

499

Ex: #5QG<cr> might return *5QG-1<cr>

500

501

The value returned above means the servo is in a counter-clockwise gyration. Sending a #5WR30 command will rotate the servo in a counter-clockwise gyration at 30 RPM.

502

503

Configure Gyre (**CG**)

Ex: #5CG-1<cr>

This changes the gyre direction as described above and also writes to EEPROM.

508

509

====== __First Position__ ======

510

511

In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. Note that the number should be restricted to -1790 (-179.0 degrees) to +1790 (179.0 degrees) and values beyond this will be changed to 1800.Query First Position in Degrees (**QFD**)Ex: #5QFD<cr> might return *5QFD900<cr>The reply above indicates that servo with ID 5 has a first position of 90.0 degrees. If there is no first position value stored, the reply will be DIS.Configure First Position in Degrees (**CFD**)Ex: #5CFD900<cr>This configuration command means the servo, when set to smart mode, will immediately move to 90.0 degrees upon power up. Sending a CFD command without a number (Ex. #5CFD<cr>) results in the servo remaining limp upon power up. In order to remove the first position, send no value, ex: #5CFD<cr>

512

513

====== __Maximum Speed in Degrees (**SD**)__ ======

514

515

Ex: #5SD1800<cr>This command sets the servo's maximum speed for motion commands in tenths of degrees per second for that session. In the example above, the servo's maximum speed for that session would be set to 180.0 degrees per second. The servo's maximum speed cannot be set higher than its physical limit at a given voltage. The SD action command overrides CSD (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSD as described below. Note that SD and SR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) received is what the servo uses for that session.Query Speed in Degrees (**QSD**)Ex: #5QSD<cr> might return *5QSD1800<cr>By default QSD will return the current session value, which is set to the value of CSD as reset/power cycle and changed whenever an SD/SR command is processed. If #5QSD1<cr> is sent, the configured maximum speed (CSD value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:

516

517

|**Command sent**|**Returned value (1/10 °)**

518

|ex: #5QSD<cr>|Session value for maximum speed (set by latest SD/SR command)

519

|ex: #5QSD1<cr>|Configured maximum speed in EEPROM (set by CSD/CSR)

520

|ex: #5QSD2<cr>|Instantaneous speed (same as QWD)

521

|ex: #5QSD3<cr>|Target travel speed

522

523

Configure Speed in Degrees (**CSD**)Ex: #5CSD1800<cr>Using the CSD command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 180.0 degrees per second. When the servo is powered on (or after a reset), the CSD value is used. Note that CSD and CSR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.

524

525

====== __Maximum Speed in RPM (**SR**)__ ======

526

527

Ex: #5SR45<cr>This command sets the servo's maximum speed for motion commands in rpm for that session. In the example above, the servo's maximum speed for that session would be set to 45rpm. The servo's maximum speed cannot be set higher than its physical limit at a given voltage. SR overrides CSR (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSR as described below. Note that SD (described above) and SR are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) received is what the servo uses for that session.Query Speed in RPM (**QSR**)Ex: #5QSR<cr> might return *5QSR45<cr>By default QSR will return the current session value, which is set to the value of CSR as reset/power cycle and changed whenever an SD/SR command is processed. If #5QSR1<cr> is sent, the configured maximum speed (CSR value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:

528

529

|**Command sent**|**Returned value (1/10 °)**

530

|ex: #5QSR<cr>|Session value for maximum speed (set by latest SD/SR command)

531

|ex: #5QSR1<cr>|Configured maximum speed in EEPROM (set by CSD/CSR)

532

|ex: #5QSR2<cr>|Instantaneous speed (same as QWD)

533

|ex: #5QSR3<cr>|Target travel speed

534

535

Configure Speed in RPM (**CSR**)Ex: #5CSR45<cr>Using the CSR command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSR value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) received is what the servo uses for that session.

536

537

====== __Step Mode (**SM**)__ ======

Ex: #8SM2<cr>

This sets servo with ID 8 to 1/2 step mode. Since this is an action as opposed to a configuration, it only affects that session.

542

543

Note that the torque and max RPM of the actuator will be affected.

544

545

Query Step Mode (**QSM**)

546

547

Ex: #8QSM<cr> might return *8QSM2<cr> meaning servo with ID 8 is set to half step mode.

548

549

Configure Step Mode (**CSM**)

Ex: #8SM2<cr>

This sets servo with ID 8 to 1/2 step mode. Since this is a configuration as opposed to a configuration and the servo will be in 1/2 step mode when powered.

== Modifiers ==

====== __Speed (**SD**) modifier__ ======

558

559

(% class="wikigeneratedid" id="HTimedmove28T29modifier" %)

560

Example: #5D0SD180<cr>

561

562

(% class="wikigeneratedid" %)

563

Modifier (SD) is only for a position (D) or relative position (MD) action and determines the speed of the move in tenths of degrees per second. A speed modifier (SD) of 180 would cause the servo to rotate from its current position to the desired absolute or relative position at a speed of 18 degrees per second.

564

565

(% class="wikigeneratedid" %)

566

Query Speed (**QS**)

567

568

(% class="wikigeneratedid" %)

569

Example: #5QS<cr> might return *5QS300<cr>

570

571

(% class="wikigeneratedid" %)

572

This command queries the current speed in microseconds per second.

573

574

====== __Timed move (**T**) modifier__ ======

575

576

Example: #5D15000T2500<cr>

577

578

Timed move can be used only as a modifier for a position (D, MD) actions. The units are in milliseconds, so a timed move of 2500 milliseconds would cause the servo to rotate from its current position to the desired position in 2.5 seconds. The onboard controller will attempt to ensure that the move is performed entirely at the desired velocity, though differences in torque may cause it to not be exact. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.

579

580

**Note:** If the calculated speed at which a servo must rotate for a timed move is greater than its maximum speed (which depends on voltage and load), then it will move at its maximum speed, and the time of the move may be longer than requested

====== ======

== Telemetry ==

====== __Query PCB Temperature (**QT**)__ ======

587

588

Ex: #5QT<cr> might return *5QT564<cr>

589

590

The units are in tenths of degrees Celcius, so in the example above, the servo's internal temperature is 56.4 degrees C. To convert from degrees Celcius to degrees Farenheit, multiply by 1.8 and add 32. Therefore 56.4C = 133.52F.

591

592

====== __Query Temperature Probe (**QTP**)__ ======

Ex:

====== __Query Temp of Controller (**QTCW**)__ ======

Ex:

An alternative is QTCE

601

602

====== __Query Current (**QC**)__ ======

603

604

Ex: #5QC<cr> might return *5QC140<cr>

605

606

The units are in milliamps, so in the example above, the servo is consuming 140mA, or 0.14A. It represents the RMS value. The query calculates the RMS value of the current sent from the motor driver to the stepper motor.

607

608

====== __Query Model String (**QMS**)__ ======

609

610

Ex: #5QMS<cr> might return *5QMSLSS-HS1<cr>

611

612

This reply means that the servo model is LSS-HS1: a high speed servo, first revision.

613

614

====== __Query Firmware (**QF**)__ ======

615

616

Ex: #5QF<cr> might return *5QF368<cr>

617

618

The number in the reply represents the firmware version, in this example being 368.The command #5QF3<cr> can also be sent and the servo will reply with a 3 numbers firmware version, for example, 368.29.14

619

620

====== __Query Serial Number (**QN**)__ ======

621

622

Ex: #5QN<cr> might return *5QN12345678<cr>

623

624

The number in the response (12345678) would be the servo's serial number which is set and should not be changed by the user.

625

626

====== __Query IMU Linear (**QIX** **QIY** **QIZ**)__ ======