Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.ENantel
	1	+xwiki:XWiki.CBenson

Content

...	...	@@ -1,7 +1,5 @@
1		-
	1	+[[image:LSS-P-Configuration-Software.png||width="350"]]
2	2
3		-{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-pro/lss-pro/lss-p-configuration-software/WebHome/LSS-P-Configuration-Software.png" width="350"/}}
4		-
5	5	[[[[image:[email protected]]]>>attach:LSS_PRO_Config_Setup.zip]]
6	6
7	7	**Table of Contents**
...	...	@@ -26,9 +26,6 @@
26	26
27	27	This section provides step-by-step instructions and tips to help you get the most out of your LSS-P actuator. Whether you are setting up your hardware, configuring your servos, or troubleshooting, you'll find detailed information to assist you. Follow the guidelines below to ensure optimal performance and a smooth experience.
28	28
29		-* [[doc:.lss-p-config-configure-ids.WebHome]]
30		-* [[doc:.lss-p-config-firmware-update.WebHome]]
31		-
32	32	== Information ==
33	33
34	34	[[image:LSS-P-Config-Info.png]]
...	...	@@ -150,14 +150,14 @@
150	150	1. Save will let you do a backup of the current Custom Actions.
151	151	1. Load will let you select and load a previously saved Custom Action file.
152	152
153		-=== Personalized Action ===
	148	+=== Personalize Action ===
154	154
155		-To change the Action for a specific button, "CTRL + CLICK" on the desired button, and this interface will then be displayed:
	150	+To change the Action for a specific button, you have to do a "CTRL + CLICK" on the desired button, this interface will then be displayed.
156	156
157	157	[[image:LSS-P-Config-Custom-Actions-Custom.png]]
158	158
159	159	1. Action Name: Displayed name for that particular action.
160		-1. Two separate "Add" button and corresponding drop down menus which are shortcuts to add to the action in (3)
	155	+1. Two separate "Add" button and drop down are present, they are shortcuts to add to the action bellow.
161	161	1. Action command that will be sent to the actuator plus displayed units for the interface.
162	162
163	163	== Firmware Update ==
...	...	@@ -168,19 +168,19 @@
168	168
169	169	[[image:LSS-P-Config-Firmware-Available.png]]
170	170
171		-When a firmware update is available, the __logo will turn green__, as shown in the image above..
	166	+1. When a firmware update is available, the logo will turn green.
172	172
173	173	Note: Only a servo connected via USB can be updated and all the other servos on the bus will not be displayed with a green logo unless connected directly via USB.
174	174
175	175	=== Online Update ===
176	176
177		-1. Select the servo ID to see if a firmware update is available for that servo
	172	+1. Select the servo ID that requires a firmware update
178	178	1. If the logo is green, click on the "Firmware Update" button
179	179	1. A message will ask you if you want do download the latest firmware, click Yes.
180	180	[[image:LSS-P-Config-Firmware-Download-Yes.png||alt="LSS-P-Config-Firmware-Download.png"]]
181		-1. The time to download the update should be fast, and once downloaded another message will ask you if you want to proceed; click Yes.
	176	+1. It's pretty quick but once downloaded another message will ask you if you want to proceed click Yes.
182	182	[[image:LSS-P-Config-Firmware-Write-Acknowledge.png]]
183		-1. The servo will be put in "Firmware Update" mode and the LED on the servo will start flashing. A progress bar will show the progress. DO NOT UNPLUG or REMOVE POWER from the servo while updating.
	178	+1. The servo will be put in "Firmware Update" mode and flashing will start. A progress bar will show the progress. DO NOT UNPLUG / UNPOWER the servo while updating.
184	184	[[image:LSS-P-Config-Firmware-Uploading.png]]
185	185	1. Once the procedure is done you will have a confirmation pop-up.
186	186	[[image:LSS-P-Config-Firmware-Success.png]]
...	...	@@ -187,16 +187,16 @@
187	187
188	188	=== Offline Update ===
189	189
190		-In rare occasions, our staff could ask you to upload a firmware which they provided. A link to this procedure will also be provided.
	185	+In some rare occasions, our staff could ask you to try a firmware which they provided and here's how to flash it.
191	191
192	192	1. Select the servo ID that requires a firmware update
193	193	1. Click on the "Firmware Update" button and depending on the pop-up select as shown.
194	194	[[image:LSS-P-Config-Firmware-Download-No.png||alt="LSS-P-Config-Firmware-Download.png"]] [[image:LSS-P-Config-Firmware-Write-Yes.png||alt="LSS-P-Config-Firmware-Local.png"]]
195		-1. Browse to and select & open the firmware file provided by our staff (saved locally on your computer).
	190	+1. Browse and select & open the firmware file provided by our staff.
196	196	[[image:LSS-P-Config-Firmware-Local-Browse.png]]
197		-1. Another message will ask you if you want to proceed; click Yes.
	192	+1. Another message will ask you if you want to proceed click Yes.
198	198	[[image:LSS-P-Config-Firmware-Write-Acknowledge.png]]
199		-1. The servo will be put in "Firmware Update" mode and the LED on the servo will start flashing. A progress bar will show the progress. DO NOT UNPLUG or REMOVE POWER from the servo while updating.
	194	+1. The servo will be put in "Firmware Update" mode and flashing will start. A progress bar will show the progress. DO NOT UNPLUG / UNPOWER the servo while updating.
200	200	[[image:LSS-P-Config-Firmware-Uploading.png]]
201	201	1. Once the procedure is done you will have a confirmation pop-up.
202	202	[[image:LSS-P-Config-Firmware-Success.png]]