Changes for page LSS-PRO Configure IDs

Last modified by Coleman Benson on 2024/10/08 12:52
From version < 13.1 >
edited by Eric Nantel
on 2024/07/25 11:38
To version < 23.1 >
edited by Eric Nantel
on 2024/09/19 13:36
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,9 @@
1 -= Step 1 - Connections =
1 +(% style="width:710px" %)
2 +|(% colspan="2" %)(((
3 += LSS-PRO Configure IDs =
4 +)))
5 +|(% style="width:25px" %) |(((
6 +~1. Wiring
2 2  
3 3  __Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__
4 4  
... ... @@ -6,39 +6,61 @@
6 6  Connect the XT60 from your power supply
7 7  )))
8 8  * Connect the USB Type-C cable
14 +)))
15 +| |(((
16 +2. Power-Up
9 9  
10 -= Step 2 - Power-Up =
11 -
12 12  * Proceed with powering the actuator
19 +)))
20 +| |(((
21 +3. LSS PRO Config Software
13 13  
14 -= Step 3 - Software =
15 -
16 -* Install the LSS PRO Configuration software ([[HERE>>doc:ses-pro.lss-pro.lss-p-configuration-software.WebHome]])
23 +* Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]])
17 17  * Open the LSS PRO Configuration software
18 18  
19 19  [[image:LSS-P-ID-Config-Open.png]]
27 +)))
28 +| |(((
29 +4. Connection
20 20  
21 -= Step 4 - Connection =
22 -
23 23  * Select the COM port associated with your actuator
24 24  * Click Connect
25 25  
26 26  [[image:LSS-P-ID-Config-COM.png]]
35 +)))
36 +| |(((
37 +5. Actuator Selection
27 27  
28 -= Step 5 - Selection =
29 -
30 30  * In the drop-down menu, select your actuator
31 31  
32 -= Step 6 - Set the ID =
41 +[[image:LSS-P-ID-Config-Select.png]]
42 +)))
43 +| |(((
44 +6. Set the ID
33 33  
34 34  * In the "Configuration" drop-down menu, select "CID / ID Number"
47 +
48 +[[image:LSS-P-ID-Config-CID.png]]
49 +
35 35  * In the text entry box, set the desired ID number
51 +
52 +[[image:LSS-P-ID-Config-ID1.png]]
53 +
36 36  * Click on the "Send" button
55 +
56 +[[image:LSS-P-ID-Config-Send.png]]
57 +
37 37  * The "RESET" button will start blinking, click on it to reset
38 38  
39 -= Step 7 - Confirm =
60 +[[image:LSS-P-ID-Config-Reset.png]]
61 +)))
62 +| |(((
63 +7. Confirm
40 40  
41 41  * The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4
42 42  * Verify that your ID is not what you have set it at
43 43  
68 +[[image:LSS-P-ID-Config-ID1-Confirm.png]]
69 +
44 44  At that point your Actuator should have the new ID configured.
71 +)))
LSS-P-ID-Config-Reset.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +7.8 KB
Content
LSS-P-ID-Config-Send.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +17.5 KB
Content
Copyright RobotShop 2018