Changes for page LSS-PRO Configure IDs

Last modified by Coleman Benson on 2024/10/08 12:52
From version < 24.1 >
edited by Eric Nantel
on 2024/09/19 13:39
To version < 3.1 >
edited by Eric Nantel
on 2024/07/25 10:27
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,71 +1,23 @@
1 -(% style="width:710px" %)
2 -|(% colspan="2" %)(((
3 -= LSS-PRO Configure IDs =
4 -)))
5 -|(% style="width:25px" %) |(((
6 -~1. Wiring
1 +
7 7  
8 -__Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__
9 9  
10 -* (((
11 -Connect the XT60 from your power supply
12 -)))
13 -* Connect the USB Type-C cable
14 -)))
15 -| |(((
16 -2. Power-Up
4 +|(% colspan="2" %)Step 1
5 +|(% style="width:30px" %) |While your power supply is OFF (important) connect the Servo power and USB cables
6 +|(% colspan="2" %)Step 2
7 +| |Power up your supply
8 +|(% colspan="2" %)
9 +| |Open the LSS PRO Configuration software (HERE)
10 +|(% colspan="2" %)
11 +| |Select the COM port associated with your actuator & connect
12 +|(% colspan="2" %)
13 +| |Select your actuator from the drop-down list
14 +|(% colspan="2" %)
15 +| |Select the CID configuration command in the list
16 +|(% colspan="2" %)
17 +| |Set the desired ID in the text box
18 +|(% colspan="2" %)
19 +| |Send your command
20 +|(% colspan="2" %)
21 +| |Reset your actuator
17 17  
18 -* Proceed with powering the actuator
19 -)))
20 -| |(((
21 -3. LSS PRO Config Software
22 -
23 -* Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]])
24 -* Open the LSS PRO Configuration software
25 -
26 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Open.png]]
27 -)))
28 -| |(((
29 -4. Connection
30 -
31 -* Select the COM port associated with your actuator
32 -* Click Connect
33 -
34 -[[image:LSS-P-ID-Config-COM.png]]
35 -)))
36 -| |(((
37 -5. Actuator Selection
38 -
39 -* In the drop-down menu, select your actuator
40 -
41 -[[image:LSS-P-ID-Config-Select.png]]
42 -)))
43 -| |(((
44 -6. Set the ID
45 -
46 -* In the "Configuration" drop-down menu, select "CID / ID Number"
47 -
48 -[[image:LSS-P-ID-Config-CID.png]]
49 -
50 -* In the text entry box, set the desired ID number
51 -
52 -[[image:LSS-P-ID-Config-ID1.png]]
53 -
54 -* Click on the "Send" button
55 -
56 -[[image:LSS-P-ID-Config-Send.png]]
57 -
58 -* The "RESET" button will start blinking, click on it to reset
59 -
60 -[[image:LSS-P-ID-Config-Reset.png]]
61 -)))
62 -| |(((
63 -7. Confirm
64 -
65 -* The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4
66 -* Verify that your ID is not what you have set it at
67 -
68 -[[image:LSS-P-ID-Config-ID1-Confirm.png]]
69 -
70 -At that point your Actuator should have the new ID configured.
71 -)))
23 +
LSS-P-ID-Config-CID.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -33.9 KB
Content
LSS-P-ID-Config-COM.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -12.4 KB
Content
LSS-P-ID-Config-ID1-Confirm.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -6.6 KB
Content
LSS-P-ID-Config-ID1.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -17.4 KB
Content
LSS-P-ID-Config-Open.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -178.7 KB
Content
LSS-P-ID-Config-Reset.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -7.8 KB
Content
LSS-P-ID-Config-Select.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -6.5 KB
Content
LSS-P-ID-Config-Send.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -17.5 KB
Content
Copyright RobotShop 2018