Changes for page LSS-PRO Configure IDs

Last modified by Coleman Benson on 2024/10/08 12:52
From version < 27.1
edited by Coleman Benson
on 2024/10/08 12:52
To version < 2.1 >
edited by Eric Nantel
on 2024/07/03 08:56
<
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -xwiki:XWiki.CBenson
1 +xwiki:XWiki.ENantel
Content
... ... @@ -1,74 +1,0 @@
1 -(% style="width:710px" %)
2 -|(% colspan="2" %)(((
3 -== LSS-PRO Configure IDs ==
4 -)))
5 -|(% style="width:25px" %) |(((
6 -~1. Wiring
7 -
8 -__WARNING:**Do not hot plug the servo!** Make sure the power supply is turned OFF (and waited at least 10s for it to completely discharge its internal capacitor) before connecting it to the LSS-P actuator__
9 -
10 -* (((
11 -Connect the XT60 from your power supply
12 -)))
13 -* Connect the USB Type-C cable
14 -
15 -If you are using a battery, ensure there is an On/Off switch between the battery and the servo(s).
16 -)))
17 -| |(((
18 -2. Power ON
19 -
20 -* Power the actuator (set the switch to ON)
21 -)))
22 -| |(((
23 -3. LSS PRO Config Software
24 -
25 -* Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]])
26 -* Open the LSS PRO Configuration software
27 -
28 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Open.png]]
29 -)))
30 -| |(((
31 -4. Connect to the BUS
32 -
33 -* Select the COM port associated with your actuator or the first servo in the BUS
34 -* Click Connect
35 -
36 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-COM.png]]
37 -)))
38 -| |(((
39 -5. Actuator Selection
40 -
41 -* In the drop-down menu, select your actuator
42 -
43 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Select.png]]
44 -)))
45 -| |(((
46 -6. Set the servo's ID
47 -
48 -* In the "Configuration" drop-down menu, select the **C**onfigure **ID** command "CID / ID Number"
49 -
50 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-CID.png]]
51 -
52 -* In the text entry box, set the desired ID number (integers only up to 253)
53 -
54 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-ID1.png]]
55 -
56 -* Click on the "Send" button to send the command to the servo
57 -
58 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Send.png]]
59 -
60 -* The "RESET" button will start blinking, click on it to reset the servo
61 -
62 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Reset.png]]
63 -)))
64 -| |(((
65 -7. Confirm
66 -
67 -* The software will automatically re-connect to the actuator but if not, proceed as done in Step 4
68 -* Verify that your ID is not what you have set
69 -
70 -[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-ID1-Confirm.png]]
71 -
72 -At that point your Actuator should have the new ID configured.
73 -)))
74 -| |8. Repeat individualls for each servo in the BUS ensuring only one servo at a time is connected via its own USB to the software.
LSS-P-ID-Config-CID.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -33.9 KB
Content
LSS-P-ID-Config-COM.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -12.4 KB
Content
LSS-P-ID-Config-ID1-Confirm.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -6.6 KB
Content
LSS-P-ID-Config-ID1.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -17.4 KB
Content
LSS-P-ID-Config-Open.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -178.7 KB
Content
LSS-P-ID-Config-Reset.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -7.8 KB
Content
LSS-P-ID-Config-Select.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -6.5 KB
Content
LSS-P-ID-Config-Send.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -17.5 KB
Content
Copyright RobotShop 2018