Changes for page LSS-PRO Configure IDs
Last modified by Coleman Benson on 2024/10/08 12:52
Change comment: There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 8 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,23 +1,67 @@ 1 - 1 += Step 1 - Connections = 2 2 3 +__Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__ 3 3 4 -|(% colspan="2" %)Step 1 5 -|(% style="width:30px" %) |While your power supply is OFF (important) connect the Servo power and USB cables 6 -|(% colspan="2" %)Step 2 7 -| |Power up your supply 8 -|(% colspan="2" %) 9 -| |Open the LSS PRO Configuration software (HERE) 10 -|(% colspan="2" %) 11 -| |Select the COM port associated with your actuator & connect 12 -|(% colspan="2" %) 13 -| |Select your actuator from the drop-down list 14 -|(% colspan="2" %) 15 -| |Select the CID configuration command in the list 16 -|(% colspan="2" %) 17 -| |Set the desired ID in the text box 18 -|(% colspan="2" %) 19 -| |Send your command 20 -|(% colspan="2" %) 21 -| |Reset your actuator 5 +* ((( 6 +Connect the XT60 from your power supply 7 +))) 8 +* Connect the USB Type-C cable 22 22 23 - 10 += Step 2 - Power-Up = 11 + 12 +* Proceed with powering the actuator 13 + 14 += Step 3 - Software = 15 + 16 +* Install the LSS PRO Configuration software ([[HERE>>doc:ses-pro.lss-pro.lss-p-configuration-software.WebHome]]) 17 +* Open the LSS PRO Configuration software 18 + 19 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-Open.png]] 20 + 21 + 22 += Step 4 - Connection = 23 + 24 +* Select the COM port associated with your actuator 25 +* Click Connect 26 + 27 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-COM.png]] 28 + 29 + 30 += Step 5 - Selection = 31 + 32 +* In the drop-down menu, select your actuator 33 + 34 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-Select.png]] 35 + 36 + 37 += Step 6 - Set the ID = 38 + 39 +* In the "Configuration" drop-down menu, select "CID / ID Number" 40 + 41 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-CID.png]] 42 + 43 + 44 +* In the text entry box, set the desired ID number 45 + 46 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-ID1.png]] 47 + 48 + 49 +* Click on the "Send" button 50 + 51 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-Send.png]] 52 + 53 + 54 +* The "RESET" button will start blinking, click on it to reset 55 + 56 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-Reset.png]] 57 + 58 + 59 += Step 7 - Confirm = 60 + 61 +* The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4 62 +* Verify that your ID is not what you have set it at 63 + 64 +|(% style="width:35px" %) |[[image:LSS-P-ID-Config-ID1-Confirm.png]] 65 + 66 + 67 +At that point your Actuator should have the new ID configured.
- LSS-P-ID-Config-CID.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +33.9 KB - Content
- LSS-P-ID-Config-COM.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +12.4 KB - Content
- LSS-P-ID-Config-ID1-Confirm.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +6.6 KB - Content
- LSS-P-ID-Config-ID1.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +17.4 KB - Content
- LSS-P-ID-Config-Open.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +178.7 KB - Content
- LSS-P-ID-Config-Reset.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +7.8 KB - Content
- LSS-P-ID-Config-Select.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +6.5 KB - Content
- LSS-P-ID-Config-Send.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +17.5 KB - Content