Wiki source code of LSS-PRO Configure IDs
Version 21.1 by Eric Nantel on 2024/07/25 12:02
Hide last authors
 |
4.1 | 1 | = Step 1 - Connections = |
| |
2.2 | 2 | |
| |
4.1 | 3 | __Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__ |
| |
2.2 | 4 | |
| |
4.1 | 5 | * ((( |
| 6 | Connect the XT60 from your power supply | ||
| 7 | ))) | ||
| 8 | * Connect the USB Type-C cable | ||
| |
2.2 | 9 | |
| |
4.1 | 10 | = Step 2 - Power-Up = |
| 11 | |||
| 12 | * Proceed with powering the actuator | ||
| 13 | |||
| |
21.1 | 14 | = Step 3 - Software = |
| |
20.1 | 15 | |
| |
5.1 | 16 | * Install the LSS PRO Configuration software ([[HERE>>doc:ses-pro.lss-pro.lss-p-configuration-software.WebHome]]) |
| |
4.1 | 17 | * Open the LSS PRO Configuration software |
| |
21.1 | 18 | |
| |
19.1 | 19 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-Open.png]] |
| |
5.1 | 20 | |
| |
21.1 | 21 | |
| |
4.1 | 22 | = Step 4 - Connection = |
| 23 | |||
| 24 | * Select the COM port associated with your actuator | ||
| 25 | * Click Connect | ||
| 26 | |||
| |
19.1 | 27 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-COM.png]] |
| |
5.1 | 28 | |
| |
21.1 | 29 | |
| |
4.1 | 30 | = Step 5 - Selection = |
| 31 | |||
| 32 | * In the drop-down menu, select your actuator | ||
| 33 | |||
| |
19.1 | 34 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-Select.png]] |
| |
16.1 | 35 | |
| |
21.1 | 36 | |
| |
4.1 | 37 | = Step 6 - Set the ID = |
| 38 | |||
| 39 | * In the "Configuration" drop-down menu, select "CID / ID Number" | ||
| |
16.1 | 40 | |
| |
19.1 | 41 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-CID.png]] |
| |
16.1 | 42 | |
| |
21.1 | 43 | |
| |
4.1 | 44 | * In the text entry box, set the desired ID number |
| |
16.1 | 45 | |
| |
19.1 | 46 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-ID1.png]] |
| |
16.1 | 47 | |
| |
21.1 | 48 | |
| |
4.1 | 49 | * Click on the "Send" button |
| |
16.1 | 50 | |
| |
19.1 | 51 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-Send.png]] |
| |
16.1 | 52 | |
| |
21.1 | 53 | |
| |
5.1 | 54 | * The "RESET" button will start blinking, click on it to reset |
| |
4.1 | 55 | |
| |
19.1 | 56 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-Reset.png]] |
| |
16.1 | 57 | |
| |
21.1 | 58 | |
| |
5.1 | 59 | = Step 7 - Confirm = |
| 60 | |||
| 61 | * The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4 | ||
| 62 | * Verify that your ID is not what you have set it at | ||
| 63 | |||
| |
19.1 | 64 | |(% style="width:35px" %) |[[image:LSS-P-ID-Config-ID1-Confirm.png]] |
| |
16.1 | 65 | |
| |
21.1 | 66 | |
| |
4.1 | 67 | At that point your Actuator should have the new ID configured. |