Wiki source code of LSS-PRO Configure IDs
Version 24.1 by Eric Nantel on 2024/09/19 13:39
Show last authors
| 1 | (% style="width:710px" %) |
| 2 | |(% colspan="2" %)((( |
| 3 | = LSS-PRO Configure IDs = |
| 4 | ))) |
| 5 | |(% style="width:25px" %) |((( |
| 6 | ~1. Wiring |
| 7 | |
| 8 | __Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__ |
| 9 | |
| 10 | * ((( |
| 11 | Connect the XT60 from your power supply |
| 12 | ))) |
| 13 | * Connect the USB Type-C cable |
| 14 | ))) |
| 15 | | |((( |
| 16 | 2. Power-Up |
| 17 | |
| 18 | * Proceed with powering the actuator |
| 19 | ))) |
| 20 | | |((( |
| 21 | 3. LSS PRO Config Software |
| 22 | |
| 23 | * Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]]) |
| 24 | * Open the LSS PRO Configuration software |
| 25 | |
| 26 | [[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Open.png]] |
| 27 | ))) |
| 28 | | |((( |
| 29 | 4. Connection |
| 30 | |
| 31 | * Select the COM port associated with your actuator |
| 32 | * Click Connect |
| 33 | |
| 34 | [[image:LSS-P-ID-Config-COM.png]] |
| 35 | ))) |
| 36 | | |((( |
| 37 | 5. Actuator Selection |
| 38 | |
| 39 | * In the drop-down menu, select your actuator |
| 40 | |
| 41 | [[image:LSS-P-ID-Config-Select.png]] |
| 42 | ))) |
| 43 | | |((( |
| 44 | 6. Set the ID |
| 45 | |
| 46 | * In the "Configuration" drop-down menu, select "CID / ID Number" |
| 47 | |
| 48 | [[image:LSS-P-ID-Config-CID.png]] |
| 49 | |
| 50 | * In the text entry box, set the desired ID number |
| 51 | |
| 52 | [[image:LSS-P-ID-Config-ID1.png]] |
| 53 | |
| 54 | * Click on the "Send" button |
| 55 | |
| 56 | [[image:LSS-P-ID-Config-Send.png]] |
| 57 | |
| 58 | * The "RESET" button will start blinking, click on it to reset |
| 59 | |
| 60 | [[image:LSS-P-ID-Config-Reset.png]] |
| 61 | ))) |
| 62 | | |((( |
| 63 | 7. Confirm |
| 64 | |
| 65 | * The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4 |
| 66 | * Verify that your ID is not what you have set it at |
| 67 | |
| 68 | [[image:LSS-P-ID-Config-ID1-Confirm.png]] |
| 69 | |
| 70 | At that point your Actuator should have the new ID configured. |
| 71 | ))) |