Changes for page LSS-PRO Electrical

Last modified by Eric Nantel on 2024/07/12 12:50
From version < 22.1 >
edited by Eric Nantel
on 2023/08/01 12:25
To version < 20.1 >
edited by Eric Nantel
on 2023/08/01 12:06
< >
Change comment: Upload new image "LSS-P-S1-Pinout-Power.png", version 1.1

Summary

Details

Page properties
Content
... ... @@ -4,10 +4,6 @@
4 4  
5 5  
6 6  
7 -
8 -
9 -
10 -
11 11  **Page Contents**
12 12  
13 13  {{toc/}}
... ... @@ -28,19 +28,17 @@
28 28  
29 29  |(% colspan="3" style="width:350px" %)**CAN Bus**
30 30  |(% style="width:350px" %) |(% style="text-align:left; vertical-align:middle; width:35px" %) |(% style="text-align:center; vertical-align:middle" %)**Serial Mode**
31 -|(% rowspan="5" style="width:350px" %)(((
32 -{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-RJ45.png"/}}
27 +|(% rowspan="3" style="width:350px" %)(((
28 +
33 33  )))|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)(((
34 34  **Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
35 35  )))
36 -|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)(((
32 +|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)(((
37 37  **Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
38 38  )))
39 -|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
40 -|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Power: **
41 -|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Not Connected:** Those pins are un-connected
35 +|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
42 42  |(% colspan="3" style="width:350px" %)**Power**
43 43  |(% colspan="1" rowspan="2" style="width:350px" %)(((
44 -{{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/lynxmotion-smart-servo-pro/lss-p-electrical/WebHome/LSS-P-S1-Pinout-Power.png"/}}
45 -)))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**:
38 +
39 +)))|(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**:
46 46  |(% style="text-align:left; vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**:
Copyright RobotShop 2018