Wiki source code of LSS FlowArm - Setup
Version 27.1 by Eric Nantel on 2022/06/20 15:01
Show last authors
| 1 | (% style="width:700px" %) |
| 2 | |(% colspan="3" %)**Connecting via USB** |
| 3 | |(% style="width:10px" %) |(% colspan="2" %)1. Connect the USB cable to the Arm and PC & Power Adapter to the Arm XT60 |
| 4 | |(% style="width:10px" %) |{{lightbox image="LSS-ADA-Power&USB-B.png"/}}|{{lightbox image="LSS-ADA-Power&USB-A.png"/}} |
| 5 | | |(% colspan="2" %)2. Power the arm using the power supply ON/OFF switch. |
| 6 | | |(% colspan="2" %)3. Start the LSS FlowArm software (available [[HERE>>https://www.robotshop.com/en/lynxmotion-lss-lss-flowarm-app-download.html]]) |
| 7 | | |(% colspan="2" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/lss-flowarm/WebHome/LSS-FlowArm.png"/}} |
| 8 | | |(% colspan="2" %)((( |
| 9 | 4. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF) |
| 10 | |
| 11 | It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200) |
| 12 | ))) |
| 13 | | |(% colspan="2" %) |
| 14 | | |(% colspan="2" %)The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port. |
| 15 | | |(% colspan="2" %) |
| 16 | |
| 17 | = Connecting via USB = |
| 18 | |
| 19 | 1. Connect the USB cable to the LSS Adapter board on your robot |
| 20 | 1. Plug the USB connector into the PC |
| 21 | 1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable |
| 22 | 1. Connect the power to the LSS Adapter via the yellow XT60 plug |
| 23 | 1. Power on the robot (On/Off switch) |
| 24 | 1. Start the LSS FlowArm software |
| 25 | 1. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF) |
| 26 | 1. It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200) |
| 27 | 1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port. |
| 28 | |
| 29 | = Calibration = |
| 30 | |
| 31 | 1. Go in "TEACH" mode with the button on the top bar. |
| 32 | 1. Manually place the arm in the correct position for your model and with the gripper closed. (see images bellow) |
| 33 | 1. Store the values or Offsets by clicking "STORE OFFSETS" |
| 34 | 1. At that point the arm should "stay" in that position once released |
| 35 | 1. Exit the "TEACH" mode by clicking it again |
| 36 | |
| 37 | = Calibration Positions = |
| 38 | |
| 39 | |(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**4 DoF**|(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**3 DoF ** |
| 40 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="lss-flowarm-left-3dof.png" width="200"]] |