Wiki source code of LSS FlowArm - Setup
Version 43.1 by Eric Nantel on 2022/06/20 15:50
Show last authors
| 1 | (% style="width:700px" %) |
| 2 | |(% colspan="5" %)**Connecting via USB** |
| 3 | |(% style="width:10px" %) |(% colspan="4" %)1. Connect the USB cable to the Arm and PC & Power Adapter to the Arm XT60 |
| 4 | |(% style="width:10px" %) |(% colspan="2" %){{lightbox image="LSS-ADA-Power&USB-B.png"/}}|(% colspan="2" %){{lightbox image="LSS-ADA-Power&USB-A.png"/}} |
| 5 | | |(% colspan="4" %)2. Power the arm using the power supply ON/OFF switch. |
| 6 | | |(% colspan="4" %)3. Start the LSS FlowArm software (available [[HERE>>https://www.robotshop.com/en/lynxmotion-lss-lss-flowarm-app-download.html]]) |
| 7 | | |(% colspan="4" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/lss-flowarm/WebHome/LSS-FlowArm.png"/}} |
| 8 | | |(% colspan="4" %)((( |
| 9 | 4. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF) |
| 10 | |
| 11 | It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200) |
| 12 | ))) |
| 13 | | |(% colspan="4" %){{lightbox image="LSS-FlowArm-Arm-Selection.png"/}} |
| 14 | | |(% colspan="4" %)5. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port. |
| 15 | | |(% colspan="2" %){{lightbox image="LSS-FlowArm-COM-Searching.png"/}}|(% colspan="2" %){{lightbox image="LSS-FlowArm-COM-Found.png"/}} |
| 16 | |
| 17 | (% style="width:700px" %) |
| 18 | |(% colspan="5" %)**Calibration (Store Offsets)** |
| 19 | |(% style="width:10px" %) |(% colspan="4" %)((( |
| 20 | 1. Go in "TEACH" mode with the button on the top bar. |
| 21 | ))) |
| 22 | |(% style="width:10px" %) |(% colspan="4" %){{lightbox image="LSS-FlowArm-Teach.png"/}} |
| 23 | |(% style="width:10px" %) |(% colspan="4" rowspan="1" %)2. Manually place the arm in the correct position for your model and with the gripper closed. (see images bellow) |
| 24 | |(% style="width:10px" %) |(% colspan="2" style="text-align:center; width:345px" %)4DOF / 5DOF|(% colspan="2" style="text-align:center; width:345px" %)3DOF |
| 25 | |(% style="width:10px" %) |(% colspan="4" %){{lightbox image="LSS-FlowArm-Calibration.png"/}} |
| 26 | |(% style="width:10px" %) |(% colspan="4" %)3. Store the values or Offsets by clicking "STORE OFFSETS" |
| 27 | |(% style="width:10px" %) |(% colspan="4" %)4.At that point the arm should "stay" in that position once released |
| 28 | |(% style="width:10px" %) |(% colspan="4" %)5. Exit the "TEACH" mode by clicking it again |
| 29 | |(% style="width:10px" %) |(% colspan="4" %) |