Wiki source code of LSS FlowArm - Setup
Version 48.1 by Eric Nantel on 2022/06/20 15:57
Hide last authors
 |
47.1 | 1 | **Page Contents** |
| 2 | |||
| |
26.1 | 3 | (% style="width:700px" %) |
| |
48.1 | 4 | |(% colspan="5" %)((( |
| 5 | = **Connecting via USB** = | ||
| 6 | ))) | ||
| |
29.1 | 7 | |(% style="width:10px" %) |(% colspan="4" %)1. Connect the USB cable to the Arm and PC & Power Adapter to the Arm XT60 |
| 8 | |(% style="width:10px" %) |(% colspan="2" %){{lightbox image="LSS-ADA-Power&USB-B.png"/}}|(% colspan="2" %){{lightbox image="LSS-ADA-Power&USB-A.png"/}} | ||
| 9 | | |(% colspan="4" %)2. Power the arm using the power supply ON/OFF switch. | ||
| 10 | | |(% colspan="4" %)3. Start the LSS FlowArm software (available [[HERE>>https://www.robotshop.com/en/lynxmotion-lss-lss-flowarm-app-download.html]]) | ||
| 11 | | |(% colspan="4" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/ses-software/lss-flowarm/WebHome/LSS-FlowArm.png"/}} | ||
| 12 | | |(% colspan="4" %)((( | ||
| |
27.1 | 13 | 4. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF) |
| 14 | |||
| 15 | It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200) | ||
| 16 | ))) | ||
| |
31.1 | 17 | | |(% colspan="4" %){{lightbox image="LSS-FlowArm-Arm-Selection.png"/}} |
| |
33.1 | 18 | | |(% colspan="4" %)5. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port. |
| 19 | | |(% colspan="2" %){{lightbox image="LSS-FlowArm-COM-Searching.png"/}}|(% colspan="2" %){{lightbox image="LSS-FlowArm-COM-Found.png"/}} | ||
| |
9.1 | 20 | |
| |
38.1 | 21 | (% style="width:700px" %) |
| |
48.1 | 22 | |(% colspan="5" %)((( |
| 23 | = **Calibration (Store Offsets)** = | ||
| 24 | ))) | ||
| |
42.1 | 25 | |(% style="width:10px" %) |(% colspan="4" %)((( |
| 26 | 1. Go in "TEACH" mode with the button on the top bar. | ||
| 27 | ))) | ||
| 28 | |(% style="width:10px" %) |(% colspan="4" %){{lightbox image="LSS-FlowArm-Teach.png"/}} | ||
| |
44.1 | 29 | |(% style="width:10px" %) |(% colspan="4" rowspan="1" %)((( |
| 30 | 2. Manually place the physical arm in the correct position for your model and with the gripper closed and keep it in this position until the next step is done. (see images bellow) | ||
| 31 | ))) | ||
| |
42.1 | 32 | |(% style="width:10px" %) |(% colspan="2" style="text-align:center; width:345px" %)4DOF / 5DOF|(% colspan="2" style="text-align:center; width:345px" %)3DOF |
| 33 | |(% style="width:10px" %) |(% colspan="4" %){{lightbox image="LSS-FlowArm-Calibration.png"/}} | ||
| |
40.1 | 34 | |(% style="width:10px" %) |(% colspan="4" %)3. Store the values or Offsets by clicking "STORE OFFSETS" |
| |
44.1 | 35 | |(% style="width:10px" %) |(% colspan="4" %){{lightbox image="LSS-FlowArm-Store-Offsets.png"/}} |
| |
46.1 | 36 | |(% style="width:10px" %) |(% colspan="4" %)4. At that point the arm should "stay" in that position once released |
| |
40.1 | 37 | |(% style="width:10px" %) |(% colspan="4" %)5. Exit the "TEACH" mode by clicking it again |