Wiki source code of LSS FlowArm - Setup
Version 8.1 by Eric Nantel on 2022/06/20 11:07
Show last authors
| 1 | (% style="width:700px" %) |
| 2 | |(% colspan="2" %) |
| 3 | |(% style="width:350px" %)Connect the USB cable between your Arm and PC|(% colspan="1" rowspan="2" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-4dof-arm/4dof-arm-quickstart/4dof-electronics/WebHome/SESV2-LSS-ARTICULATED-ARM-ELECTRONICS-Step-03-B.PNG?="/}} |
| 4 | |Connect the power adapter XT60 to your Arm |
| 5 | |Power on the robot with the power supply ON/OFF switch| |
| 6 | |Start the LSS FlowArm software| |
| 7 | |Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF)| |
| 8 | |It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200)| |
| 9 | |The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port.| |
| 10 | |
| 11 | = Connecting via USB = |
| 12 | |
| 13 | 1. Connect the USB cable to the LSS Adapter board on your robot |
| 14 | 1. Plug the USB connector into the PC |
| 15 | 1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable |
| 16 | 1. Connect the power to the LSS Adapter via the yellow XT60 plug |
| 17 | 1. Power on the robot (On/Off switch) |
| 18 | 1. Start the LSS FlowArm software |
| 19 | 1. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF) |
| 20 | 1. It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200) |
| 21 | 1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port. |
| 22 | |
| 23 | = Calibration = |
| 24 | |
| 25 | 1. Go in "TEACH" mode with the button on the top bar. |
| 26 | 1. Manually place the arm in the correct position for your model and with the gripper closed. (see images bellow) |
| 27 | 1. Store the values or Offsets by clicking "STORE OFFSETS" |
| 28 | 1. At that point the arm should "stay" in that position once released |
| 29 | 1. Exit the "TEACH" mode by clicking it again |
| 30 | |
| 31 | = Calibration Positions = |
| 32 | |
| 33 | |(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**4 DoF**|(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**3 DoF ** |
| 34 | |(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="lss-flowarm-left-3dof.png" width="200"]] |