Last modified by Eric Nantel on 2024/07/12 11:23
From version < 155.1 >
edited by Eric Nantel
on 2019/05/15 15:09
To version < 148.1 >
edited by RB1
on 2019/05/15 14:51
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -xwiki:XWiki.ENantel
1 +xwiki:XWiki.RB1
Content
... ... @@ -1,13 +1,9 @@
1 1  {{lightbox image="lss-config-full-window-0001.png" width="520"/}}
2 2  
3 -[[[[image:wiki-download.png]]>>https://www.robotshop.com/en/lynxmotion-smart-servo-lss-configuration-software.html||target="_blank"]]
4 -
5 5  **Table of Contents**
6 6  
7 7  {{toc/}}
8 8  
9 -= Description =
10 -
11 11  The LSS Configuration software ("LSS Config" for short) is intended to provide easy access to the main features and functionality of the [[Lynxmotion Smart Servo Motors>>doc:lynxmotion-smart-servo.WebHome]], as well as providing access to firmware updates.
12 12  
13 13  NOTE: Only one servo should be connected to the software at any time. The servo must be powered correctly and in serial mode. Should your servo NOT be in serial mode, please refer to the [[button menu>>doc:lynxmotion-smart-servo.lss-button-menu.WebHome]].
... ... @@ -62,7 +62,7 @@
62 62  
63 63  {{lightbox image="lss-config-configurations.jpg" width="350"/}}
64 64  
65 -Upon connection, the software will read all configuration values and update the values in the "configurations" section. Visit the [[doc:lynxmotion-smart-servo.lss-communication-protocol.WebHome]] page for more information about commands, actions and configurations.
61 +Upon connection, the software will read all configuration values and update the values in the "configurations" section. Visit the [[doc:lynxmotion-smart-servo.lss-communication-protocol.WebHome]] page for more information about commands, actions and configurations.
66 66  
67 67  Changing the values will not affect the session. Values which have been changed will have a yellow background. The values which can be entered are restricted to what the servo can accept; for example, servo IDs must be below 250.
68 68  
... ... @@ -107,14 +107,6 @@
107 107  
108 108  = Command Line{{lightbox image="lss-config-terminal-0001" width="521"/}} =
109 109  
110 -[[image:/info/wiki/lynxmotion/download/lynxmotion-smart-servo/lss-configuration-software/WebHome/lss-config-terminal-0001||width="521"]]
111 -
112 -
113 -
114 -[[image:/info/wiki/lynxmotion/download/lynxmotion-smart-servo/lss-configuration-software/WebHome/lss-config-terminal-0001||width="521"]]
115 -
116 -
117 -
118 118  The custom command line interface both allows you to communicate directly with an individual servo, send commands to it (and view replies), as well as get responses to queries from the software. Within the command interface, you might see the following:
119 119  
120 120  |(% style="width:114px" %)**>>**|(% style="width:1364px" %)Command sent to the servo
lss-config-1000px.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.ENantel
Size
... ... @@ -1,1 +1,0 @@
1 -279.7 KB
Content
wiki-download.png
Author
... ... @@ -1,1 +1,0 @@
1 -xwiki:XWiki.CBenson
Size
... ... @@ -1,1 +1,0 @@
1 -3.9 KB
Content

Navigation

Copyright RobotShop 2018