Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • lss-config-firmware-update.jpg

Details

Page properties

Content

...	...	@@ -14,16 +14,8 @@
14	14
15	15	== Firmware Update ==
16	16
17		-[[image:lss-config-firmware-update.jpg||alt="LSS Config Firmware Update"]]
	17	+The LSS Config serves as the main software to update the servo's onboard firmware / programming. An internet connection is needed in order for the software to check if an online update is available. Do not disconnect the servo during a firmware update. During the update, a progress bar will be displayed in the command line.
18	18
19		-The LSS Config serves as the main software to update the servo's onboard firmware / programming. An internet connection is needed in order for the software to check if an online update is available.
20		-
21		-The servo's current firmware version is displayed to the left of the FIRMWARE button. Pressing the button will open a popup window which allows you to select the firmware version to upload to the servo.
22		-
23		-When checked, the Exp. button will allow experimental versions of the firmware to be displayed in the list.
24		-
25		-Do not disconnect the servo during a firmware update. During the update, a progress bar will be displayed in the command line.
26		-
27	27	= Servo Control =
28	28
29	29	The servo control section allows you to visually move the servo and change a variety of parameter.
...	...	@@ -38,13 +38,13 @@
38	38
39	39	Upon connection, the software will read all configuration values and update the values in the "configurations" section. Visit the [[LSS Communication Protocol>>doc:LSS - Overview (DEV).LSS - Communication Protocol.WebHome]] page for more information about commands, actions and configurations.
40	40
41		-Changing the values will not affect the session. Values which have been changed will have a yellow background. The values which can be entered are restricted to what the servo can accept; for example, servo IDs must be below 250.
	33	+Changing the values will not affect the session. Values which have been changed will have a yellow background.
42	42
43		-**UPDATE** Pressing this button will write all values to EEPROM, changing the configurations, and reverting all background colors to white.
	35	+Pressing the **UPDATE** button will write all values to EEPROM, changing the configurations, and reverting all background colors to white.
44	44
45		-**UNDO ALL** is a shortcut button which reverts all changes made which have not been written to EEPROM.
	37	+The **UNDO ALL** is a shortcut button which reverts all changes made which have not been written to EEPROM.
46	46
47		-**SMART** / **RC POS** / **RC WHL**: This is a shortcut to change the servo's mode (LSS Smart Serial / RC PWM Position / RC PWM Wheel). IMPORTANT NOTE: Should you select either of the two RC modes, the LSS Config software will no longer be able to communicate with the servo. You must use the button menu to return to LSS serial mode (hold the button, release, press twice).
	39	+MODE (**SMART** / **RC POS** / **RC WHL**): This is a shortcut to change the servo's mode (LSS Smart Serial / RC PWM Position / RC PWM Wheel). IMPORTANT NOTE: Should you select either of the two RC modes, the LSS Config software will no longer be able to communicate with the servo. You must use the button menu to return to LSS serial mode (hold the button, release, press twice).
48	48
49	49	= Sensor Graph =
50	50

lss-config-firmware-update.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-xwiki:XWiki.RB1

Size

...	...	@@ -1,1 +1,0 @@
1		--1 bytes

Content