Changes for page LSS Configuration Software
Last modified by Eric Nantel on 2024/07/12 11:23
Change comment: Upload new image "lss-config-20.7.14.2-carets-angular-range-64.png", version 1.1
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 4 removed)
Details
- Page properties
-
- Content
-
... ... @@ -100,20 +100,14 @@ 100 100 101 101 The servo control section allows you to visually move the servo and change a variety of parameters, including: 102 102 103 -* [[image:lss-config-20.7.14.2-carets-position-64 .png]]Position: pale blue caret104 -* [[image:lss-config-20.7.14.2-carets-offset-64.png]]Origin offset: magenta caret105 -* [[image:lss-config-20.7.14.2-carets-angular-range-64.png]]Angular range: magenta square carets106 -* [[image:lss-config-20.7.14.2-carets-speed-64.png]]RPM: green arrow / indicator107 -* [[image:lss-config-20.7.14.2-carets-first-position-64.png]]Initial position: dark blue caret103 +* Position: pale blue caret 104 +* Origin offset: magenta caret 105 +* Angular range: magenta square carets 106 +* RPM: green arrow / indicator 107 +* Initial position: dark blue caret 108 108 109 -At the lower left the servo model and the LED color (session value) are shown.109 +At the lower left the servo model and the LED color are shown. 110 110 111 -To change a value, simple use the left mouse button to hold and drag the relevant caret around its ring. Letting go of the left mouse button will update the value right away. While holding the left mouse button you can also press the right mouse button to cancel the current change to that caret (happens after right mouse click and then letting go of the left mouse button). 112 - 113 -If the caret moved is position, this will send a position command in tenths of degrees right away to the servo (#[id]D[pos]\r). 114 -If the caret moved is first position, offset or angular range then it will update the appropiate configuration (see below for details), pending an update confirmation. 115 -The speed caret cannot be moved directly; it only serves only as a display of the current speed. 116 - 117 117 == Configurations == 118 118 119 119 {{lightbox image="lss-config-configurations.jpg" width="350"/}} ... ... @@ -194,9 +194,8 @@ 194 194 |(% style="width:114px" %)**>>**|(% style="width:1364px" %)Command sent to the servo 195 195 |(% style="width:114px" %)**<<**|(% style="width:1364px" %)Reply from the servo 196 196 |(% style="width:114px" %)**INF ::**|(% style="width:1364px" %)Information 197 -|(% style="width:114px" %)**[bootloader]**|(% style="width:1364px" %)Information specific to bootloader mode & firmware updates191 +|(% style="width:114px" %)**[bootloader]**|(% style="width:1364px" %)Information specific to bootloader 198 198 |(% style="width:114px" %)**]]**|(% style="width:1364px" %)Failure 199 -|(% style="width:114px" %)**'**'****|(% style="width:1364px" %)? 200 200 201 201 The command line also auto-completes each command by automatically inserting "#[ID] before each command. For example, rather than typing #4D230<cr>, you need only type D230 and the software will automatically add #4 202 202
- lss-config-20.7.14.2-carets-first-position-64.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.RB1 - Size
-
... ... @@ -1,1 +1,0 @@ 1 -348 bytes - Content
- lss-config-20.7.14.2-carets-offset-64.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.RB1 - Size
-
... ... @@ -1,1 +1,0 @@ 1 -404 bytes - Content
- lss-config-20.7.14.2-carets-position-64 .png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.RB1 - Size
-
... ... @@ -1,1 +1,0 @@ 1 -420 bytes - Content
- lss-config-20.7.14.2-carets-speed-64.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.RB1 - Size
-
... ... @@ -1,1 +1,0 @@ 1 -371 bytes - Content