Summary

• Page properties (3 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 1 removed)
  • LSS-Config-BETA.png
  • lss-config-full-window-0001.png

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.CBenson
	1	+xwiki:XWiki.RB1

Tags

...	...	@@ -1,1 +1,1 @@
1		-LSS-Ref
	1	+LSS-Ref|LSS-Config

Content

...	...	@@ -1,6 +1,6 @@
1		-[[image:LSS-Config-BETA.png||queryString="width=350" width="350"]]
	1	+[[image:lss-config-full-window-0001.png||width="520"]]
2	2
3		-**Page Contents**
	3	+**Table of Contents**
4	4
5	5	{{toc/}}
6	6
...	...	@@ -19,7 +19,7 @@
19	19	* COM port selection
20	20	* Connect (toggle ON / OFF)
21	21
22		-Connection to the servo is done automatically, via any properly installed USB to serial interface like the [[LSS Adapter board>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]]. Once the servo is powered and properly connected to the computer, the COM port should appear in the COM port list. Ensure the board is recognized by the computer and if not, install the proper drivers. If you have multiple communication ports active, go to Windows -> Device Manager to determine which is appropriate for the USB to serial adapter you are using. Click CONNECT to connect to the servo. The software automatically scans all standard baud rates using ID254 (broadcast ID) and waits for a reply from the servo connected. Should an incorrect COM port be selected, the software will keep trying to connect. You must disconnect, select the correct COM port and reconnect. If you are not sure which COM port to select, in Windows, go to Device Manager -> Ports (COM & LPT) and select the port associated with the USB to serial device.
	22	+Connection to the servo is done automatically, via any properly installed USB to serial interface like the [[LSS Adapter board>>doc:servo-erector-set-system.ses-electronics.ses-modules.lss-adapter-board.WebHome]]. Once the servo is powered and properly connected to the computer, the COM port should appear in the COM port list. Ensure the board is recognized by the computer and if not, install the proper drivers. If you have multiple communication ports active, go to Windows -> Device Manager to determine which is appropriate for the USB to serial adapter you are using. Click CONNECT to connect to the servo. The software automatically scans all standard baud rates using ID254 (broadcast ID) and waits for a reply from the servo connected. Should an incorrect COM port be selected, the software will keep trying to connect. If you wish to change the COM port selected you must disconnect, select the correct COM port and reconnect. If you are not sure which COM port to select, in Windows, go to Device Manager -> Ports (COM & LPT) and select the port associated with the USB to serial device.
23	23
24	24	== Firmware Update ==
25	25
...	...	@@ -35,19 +35,21 @@
35	35
36	36	The LSS Config software serves as the main software used to update the servo's onboard firmware / programming. An internet connection is needed in order for the software to check if an online update is available. The servo's current firmware version is displayed to the left of the FIRMWARE button. Pressing the button will open a popup window which allows you to select the firmware version to upload to the servo. When checked, the Exp. button will allow experimental versions of the firmware to be displayed in the list. It also allows to load directly from a local file. Once the OK button is pressed, a progress bar will be displayed in the command line. Do not disconnect the servo during a firmware update. If the process does get interrupted, you can still upload firmware to the LSS by going into bootloader mode by holding the button at power up.
37	37
38		-= Servo Control [coming soon] =
	38	+= Servo Control =
39	39
40		-The servo control section allows you to visually move the servo and change a variety of parameters.
	40	+{{lightbox image="lss-config-control.jpg" width="350"/}}
41	41
	42	+The servo control section allows you to visually move the servo and change a variety of parameters, including:
	43	+
42	42	* Position: blue caret
43		-* First Position: magenta caret
	45	+* Origin Offset: magenta caret
44	44	* RPM: green arrow
45	45
46		-{More to come}
	48	+At the lower left, the servo model is shown, as well as the LED color.
47	47
48	48	== Configurations ==
49	49
50		-[[image:lss-config-configurations.png]]
	52	+{{lightbox image="lss-config-configurations.jpg" width="350"/}}
51	51
52	52	Upon connection, the software will read all configuration values and update the values in the "configurations" section. Visit the [[LSS Communication Protocol>>doc:lynxmotion-smart-servo.lss-communication-protocol.WebHome]] page for more information about commands, actions and configurations.
53	53
...	...	@@ -59,11 +59,11 @@
59	59
60	60	**SMART** / **RC POS** / **RC WHL**: This is a shortcut to change the servo's mode (LSS Smart Serial / RC PWM Position / RC PWM Wheel). IMPORTANT NOTE: Should you select either of the two RC modes, the LSS Config software will no longer be able to communicate with the servo. You must use the button menu to return to LSS serial mode (hold the button, release, press twice).
61	61
62		-= Telemetry Graph [coming soon] =
	64	+= Telemetry Graph =
63	63
64	64	The sensor graphing feature of the software allows you to select, display and record, with respect to time, the output from all of the servo's sensors.
65	65
66		-[[image:lss-config-graph.jpg]]
	68	+{{lightbox image="lss-config-graph.jpg" width="700"/}}
67	67
68	68	x-Axis: seconds
69	69
...	...	@@ -92,10 +92,8 @@
92	92	[[image:lss-config-300s.jpg]] [[image:lss-config-infs.jpg]]
93	93	)))|(% style="width:777px" %)Time Window (30s / 60s / 300s / Total)
94	94
95		-= Command Line =
	97	+= Command Line{{lightbox image="lss-config-command-line.jpg" width="700"/}} =
96	96
97		-[[image:lss-config-command-line.jpg||alt="LSS Config Command Line"]]
98		-
99	99	The custom command line interface both allows you to communicate directly with an individual servo, send commands to it (and view replies), as well as get responses to queries from the software. Within the command interface, you might see the following:
100	100
101	101	|(% style="width:114px" %)**>>**|(% style="width:1364px" %)Command sent to the servo

LSS-Config-BETA.png

Author

...	...	@@ -1,1 +1,0 @@
1		-xwiki:XWiki.ENantel

Size

...	...	@@ -1,1 +1,0 @@
1		-292.7 KB

Content

lss-config-full-window-0001.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.RB1

Size

...	...	@@ -1,0 +1,1 @@
	1	+230.3 KB

Content