Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,9 +1,9 @@
1	1	= Pinout =
2	2
3		-|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="width:35px" %)[[image:Lyxnmotion [email protected]]]|**Servo Rx pin**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
4		-|[[image:Lyxnmotion [email protected]]]|**Servo Vcc pin**: Refer to the Voltage section of the [[LSS - Specifications>>doc:Lynxmotion Smart Servo (LSS).LSS - Specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
5		-|[[image:Lyxnmotion [email protected]]]|**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
6		-|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Tx pin**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
	3	+|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Rx pin**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
	4	+|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc pin**: Refer to the Voltage section of the [[LSS - Specifications>>doc:Lynxmotion Smart Servo (LSS).LSS - Specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
	5	+|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
	6	+|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Tx pin**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
7	7
8	8	= Wiring =
9	9
...	...	@@ -12,3 +12,17 @@
12	12	)))
13	13	|{{lightbox image="LSS-WIRING-Multiple.PNG"/}}|
14	14	|{{lightbox image="LSS-WIRING-RC.PNG"/}}|
	15	+
	16	+|(% colspan="2" style="width:350px" %)(((
	17	+== Electronics ==
	18	+)))
	19	+|(% style="text-align:center; width:350px" %) |(((
	20	+The electronics inside the servo include the following:
	21	+
	22	+* H-bridge motor controller
	23	+* Microcontroller (Cortex M0)
	24	+* Magnetic position sensor
	25	+* Voltage sensor
	26	+* Temperature sensor
	27	+* Current sensor
	28	+)))