Changes for page LSS Electrical

Last modified by Eric Nantel on 2024/07/12 11:23
From version < 21.1 >
edited by Eric Nantel
on 2019/02/21 10:00
To version < 15.1 >
edited by Eric Nantel
on 2019/02/15 11:02
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,13 +1,9 @@
1 -**Page Contents**
1 += Pinout =
2 2  
3 -{{toc/}}
4 -
5 -= Serial Pinout =
6 -
7 -|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
8 -|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**: Refer to the Voltage section of the [[LSS - Specifications>>doc:Lynxmotion Smart Servo (LSS).LSS - Specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
3 +|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Rx pin**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
4 +|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc pin**: Refer to the Voltage section of the [[LSS - Specifications>>doc:Lynxmotion Smart Servo (LSS).LSS - Specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
9 9  |(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
10 -|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
6 +|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Tx pin**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
11 11  
12 12  = Serial Wiring =
13 13  
... ... @@ -15,16 +15,13 @@
15 15  |(% style="width:350px" %){{lightbox image="LSS-WIRING-Single.PNG"/}}|(% style="width:350px" %)(((
16 16  {{lightbox image="LSS-WIRING-Multiple.PNG"/}}
17 17  )))|
14 +|(((
15 += RC Wiring =
16 +)))| |
17 +|{{lightbox image="LSS-WIRING-RC.PNG"/}}| |
18 18  
19 -= RC Pinout & Wiring =
20 -
21 -|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-WIRING-RC.PNG"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|**Servo RC Signal:**
22 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Vcc:**
23 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Ground (GND)**
24 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**N/A: Futur Implementation**
25 -
26 26  |(% colspan="2" style="width:350px" %)(((
27 -= Electronics =
20 +== Electronics ==
28 28  )))
29 29  |(% style="text-align:center; width:350px" %) |(((
30 30  The electronics inside the servo include the following:
Copyright RobotShop 2018