Changes for page LSS Electrical

Last modified by Eric Nantel on 2024/07/12 11:23
From version < 33.1 >
edited by RB1
on 2019/03/20 15:46
To version < 35.1 >
edited by Eric Nantel
on 2019/03/29 10:53
< >
Change comment: Renamed back-links.

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -xwiki:XWiki.RB1
1 +xwiki:XWiki.ENantel
Content
... ... @@ -4,10 +4,10 @@
4 4  
5 5  = Serial Pinout =
6 6  
7 -|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:Lyxnmotion A[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
8 -|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**: Refer to the Voltage section of the [[LSS - Specifications>>doc:lynxmotion-smart-servo.lss-specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
9 -|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
10 -|(% style="text-align:left; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
7 +|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-SIDE-PinOut.png"/}}|(% style="text-align:left; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-a[email protected]]]|(% style="text-align:left; vertical-align:middle" %)**Servo Rx**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
8 +|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Vcc**: Refer to the Voltage section of the [[LSS - Specifications>>doc:lynxmotion-smart-servo.lss-specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
9 +|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
10 +|(% style="text-align:left; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="text-align:left; vertical-align:middle" %)**Servo Tx**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
11 11  
12 12  = Serial Wiring =
13 13  
... ... @@ -18,10 +18,10 @@
18 18  
19 19  = RC Pinout & Wiring =
20 20  
21 -|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-WIRING-RC.PNG"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion A[email protected]]]|(% style="vertical-align:middle" %)**Servo RC Signal: **Please refer to the [[LSS - RC PWM>>doc:lynxmotion-smart-servo.lss-rc-pwm.WebHome]] for more information regarding the RC mode and signals.
22 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="vertical-align:middle" %)**Servo Vcc: **Refer to the Voltage section of the [[LSS - Specifications>>doc:lynxmotion-smart-servo.lss-specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
23 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="vertical-align:middle" %)**Ground (GND): **This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
24 -|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion A[email protected]]]|(% style="vertical-align:middle" %)**N/A: Futur Implementation**
21 +|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-WIRING-RC.PNG"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:lynxmotion-wiki-a[email protected]]]|(% style="vertical-align:middle" %)**Servo RC Signal: **Please refer to the [[LSS - RC PWM>>doc:lynxmotion-smart-servo.lss-radio-control-pwm.WebHome]] for more information regarding the RC mode and signals.
22 +|(% style="text-align:center; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="vertical-align:middle" %)**Servo Vcc: **Refer to the Voltage section of the [[LSS - Specifications>>doc:lynxmotion-smart-servo.lss-specifications.WebHome]] page to understand which voltages are meant to be connected to this pin.
23 +|(% style="text-align:center; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="vertical-align:middle" %)**Ground (GND): **This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
24 +|(% style="text-align:center; vertical-align:middle" %)[[image:lynxmotion-wiki-a[email protected]||alt="SQUARE-Yellow.png"]]|(% style="vertical-align:middle" %)**N/A: Futur Implementation**
25 25  
26 26  = Electronics =
27 27  

Navigation

Copyright RobotShop 2018